Technical Brief

Comparison of Microscale Rapid Prototyping Techniques

[+] Author and Article Information
Gordon D. Hoople

Department of Mechanical Engineering,
University of California, Berkeley,
Berkeley, CA 94720
e-mail: ghoople@berkeley.edu

David A. Rolfe, Joanna R. Noble

Department of Mechanical Engineering,
University of California, Berkeley,
Berkeley, CA 94720

Katherine C. McKinstry

Department of Mechanical Engineering,
University of California,
Berkeley, CA 94720

David A. Dornfeld

Department of Mechanical Engineering,
Will C. Hall Family Professor of Engineering,
University of California, Berkeley,
Berkeley, CA 94720

Albert P. Pisano

Jacobs School of Engineering,
Distinguished Professor, MAE and ECE,
Walter J. Zable Endowed Chair of Engineering,
University of California, San Diego,
La Jolla, CA 92093

1Corresponding author.

Contributed by the Manufacturing Engineering Division of ASME for publication in the JOURNAL OF MICRO- AND NANO-MANUFACTURING. Manuscript received March 31, 2014; final manuscript received June 2, 2014; published online July 8, 2014. Assoc. Editor: Hongqiang Chen.

J. Micro Nano-Manuf 2(3), 034502 (Jul 08, 2014) (6 pages) Paper No: JMNM-14-1018; doi: 10.1115/1.4027810 History: Received March 31, 2014; Revised June 02, 2014

Recent advances in manufacturing techniques have opened up new interest in rapid prototyping at the microscale. Traditionally microscale devices are fabricated using photolithography, however this process can be time consuming, challenging, and expensive. This paper focuses on three promising rapid prototyping techniques: laser ablation, micromilling, and 3D printing. Emphasis is given to rapid prototyping tools that are commercially available to the research community rather those only used in manufacturing research. Due to the interest in rapid prototyping within the microfluidics community a test part was designed with microfluidic features. This test part was then manufactured using the three different rapid prototyping methods. Accuracy of the features and surface roughness were measured using a surface profilometer, scanning electron microscope (SEM), and optical microscope. Micromilling was found to produce the most accurate features and best surface finish down to ∼100 μm, however it did not achieve the small feature sizes produced by laser ablation. The 3D printed part, though easily manufactured, did not achieve feature sizes small enough for most microfluidic applications. Laser ablation created somewhat rough and erratic channels, however the process was faster and achieved features smaller than either of the other two methods.

Copyright © 2014 by ASME
Your Session has timed out. Please sign back in to continue.


Waldbaur, A., Rapp, H., Länge, K., and Rapp, B. E., 2011, “Let There be Chip—Towards Rapid Prototyping of Microfluidic Devices: One-Step Manufacturing Processes,” Anal. Methods, 3(12), pp. 2681–2716. [CrossRef]
Andersson, H., and van den Berg, A., 2004, “Microfabrication and Microfluidics for Tissue Engineering: State of the Art and Future Opportunities,” Lab Chip, 4(2), pp. 98–103. [CrossRef] [PubMed]
Modestino, M. A., Diaz-Botia, C. A., Haussener, S., Gomez-Sjoberg, R., Ager, J. W., and Segalman, R. A., 2013, “Integrated Microfluidic Test-Bed for Energy Conversion Devices,” Phys. Chem. Chem. Phys., 15(19), pp. 7050–7054. [CrossRef] [PubMed]
Khan Malek, C. G., 2006, “Laser Processing for Bio-Microfluidics Applications (Part I),” Anal. Bioanal. Chem., 385(8), pp. 1351–1361. [CrossRef] [PubMed]
Whitesides, G. M., 2006, “The Origins and the Future of Microfluidics,” Nature, 442(7101), pp. 368–373. [CrossRef] [PubMed]
Stratasys, 2014, “Polyjet Materials Data Sheet,” http://www.stratasys.com
McMaster-Carr, 2014, “More About Plastics,” http://www.mcmaster.com
Prospector, 2014, “Acrylic Typical Properties Generic Acrylic (PMMA),” http://plastics.ides.com/generics/3/c/t/acrylic-properties-processing
Epilog Laser, 2014, “Epilog Laser Product Brochure,” www.epilogfiles.com
Trotec, 2014, “Trotec Laser Machines Product Overview,” www.troteclaser.com
Universal Laser Systems, 2014, “ULS Product Line,” http://www.ulsinc.com/products/product-line/
Hong, T.-F., Ju, W.-J., Wu, M.-C., Tai, C.-H., Tsai, C.-H., and Fu, L.-M., 2010, “Rapid Prototyping of PMMA Microfluidic Chips Utilizing a CO2 Laser,” Microfluid. Nanofluid., 9(6), pp. 1125–1133. [CrossRef]
Klank, H., Kutter, J. P., and Geschke, O., 2002, “CO2-Laser Micromachining and Back-End Processing for Rapid Production of PMMA-Based Microfluidic Systems,” Lab Chip, 2(4), pp. 242–246. [CrossRef] [PubMed]
Cheng, J.-Y., Wei, C.-W., Hsu, K.-H., and Young, T.-H., 2004, “Direct-Write Laser Micromachining and Universal Surface Modification of {PMMA} for Device Development,” Sensors Actuators, B, 99(1), pp. 186–196. [CrossRef]
Gower, M., and Rizvi, N., 2000, “Applications of Laser Ablation to Microengineering,” Proc. SPIE, 4065, pp. 452–460. [CrossRef]
Ju, Y., Liao, Y., Zhang, L., Sheng, Y., Zhang, Q., Chen, D., Cheng, Y., Xu, Z., Sugioka, K., and Midorikawa, K., 2011, “Fabrication of Large-Volume Microfluidic Chamber Embedded in Glass Using Three-Dimensional Femtosecond Laser Micromachining,” Microfluid. Nanofluid., 11(1), pp. 111–117. [CrossRef]
Queste, S., Salut, R., Clatot, S., Rauch, J. Y., and Khan Malek, C. G., 2010, “Manufacture of Microfluidic Glass Chips by Deep Plasma Etching, Femtosecond Laser Ablation, and Anodic Bonding,” Microsyst. Technol., 16(8–9), pp. 1485–1493. [CrossRef]
Romoli, L., Tantussi, G., and Dini, G., 2011, “Experimental Approach to the Laser Machining of PMMA Substrates for the Fabrication of Microfluidic Devices,” Opt. Lasers Eng., 49(3), pp. 419–427. [CrossRef]
Alting, L., Kimura, F., Hansen, H. N., and Bissacco, G., 2003, “Micro Engineering,” CIRP Ann.–Manuf. Technol., 52(2), pp. 635–657. [CrossRef]
McDonald, J. P., Mistry, V. R., Ray, K. E., and Yalisove, S. M., 2006, “Femtosecond Pulsed Laser Direct Write Production of Nano- and Microfluidic Channels,” Appl. Phys. Lett., 88(18), p. 183113. [CrossRef]
Costa, L., Terekhov, A., Rajput, D., Hofmeister, W., Jowhar, D., Wright, G., and Janetopoulos, C., 2011, “Femtosecond Laser Machined Microfluidic Devices for Imaging of Cells During Chemotaxis,” J. Laser Appl., 23(4), p. 042001 [CrossRef]
Vaezi, M., Seitz, H., and Yang, S., 2012, “A Review on 3D Micro-Additive Manufacturing Technologies,” Int. J. Adv. Manuf. Technol., 67(5–8), pp. 1721–1754. [CrossRef]
Kitson, P. J., Rosnes, M. H., Sans, V., Dragone, V., and Cronin, L., 2012, “Configurable 3D-Printed Millifluidic and Microfluidic ‘Lab on a Chip’ Reactionware Devices,” Lab Chip, 12(18), pp. 3267–3271. [CrossRef] [PubMed]
Bonyár, A., Sántha, H., Varga, M., Ring, B., Vitéz, A., and Harsányi, G., 2012, “Characterization of Rapid PDMS Casting Technique Utilizing Molding Forms Fabricated by 3D Rapid Prototyping Technology (RPT),” Int. J. Mater. Form., 7(2), pp. 189–196. [CrossRef]
Objet Geometries Ltd., 2011, “New Advances in Rapid Prototyping Using Inkjet-Based 3D Printing,” http://objet.com/sites/default/files/pdfs/new-advances-in-RP.pdf
Hartnett, J., 2007, “Process Planning for Microfluidic Device Fabrication,” Master's thesis, University of California, Berkeley, Berkeley, CA.
Vijayaraghavan, A., Jayanathan, S., Helu, M., and Dornfeld, D., 2008, “Design and Fabrication of a Roller Imprinting Device for Microfluidic Device Manufacturing,” International Manufacturing Science and Engineering Conference Evanston, IL, Oct. 7–10, ASME Paper No. MSEC_ICMP2008-72202, pp. 551–560. [CrossRef]
Dornfeld, D., Min, S., and Takeuchi, Y., 2006, “Recent Advances in Mechanical Micromachining,” CIRP Ann.–Manuf. Technol., 55(2), pp. 745–768 [CrossRef]
Chae, J., Park, S. S., and Freiheit, T., 2006, “Investigation of Micro-Cutting Operations,” Int. J. Mach. Tools Manuf., 46(3–4), pp. 313–332. [CrossRef]
ObjetGeometries Ltd., 2011, “Objet Connex350 Brochure,” http://objet.com/3d-printers/connex/objet-connex350
Objet Geometries Ltd., 2012, “Objet Connex350,” http://objet.com/3d-printers/connex/objet-connex350
Objet Geometries Ltd., 2012, “Materials Overview,” http://objet.com/3d-printing-materials/overview


Grahic Jump Location
Fig. 1

A model of the sample part used to test the three fabrication methods

Grahic Jump Location
Fig. 2

Dimensions for the test part. Top view (left) and sectional views (right). Dimensions in millimeters.

Grahic Jump Location
Fig. 3

The three finished parts, coated in gold for use with a SEM

Grahic Jump Location
Fig. 4

A comparison of cross-sectional profiles made with three different manufacturing techniques

Grahic Jump Location
Fig. 5

A schematic of the methodology for measuring the minimum and maximum peg diameters for the results shown in Fig. 6

Grahic Jump Location
Fig. 6

A plot of a variety of pegs produced by each fabrication method compared to the nominal value for each peg (shown with a dotted line). The error bars show the minimum and maximum diameters for each peg using the methodology shown in Fig. 5.

Grahic Jump Location
Fig. 7

SEM images of parts manufactured 3 different ways. Note the rounded and poorly defined features in 3D printing, the scalloping produced by laser ablation, and the vertical sidewalls from micromilling. The channel is nominally 400 μm across, while the pegs are nominally 500 μm in diameter.

Grahic Jump Location
Fig. 8

A holistic comparison of the three manufacturing tools reviewed in this paper. Further out from the center indicates a more favorable ranking.



Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In