0
Research Papers

New Micro Tube Hydroforming System Based on Floating Die Assembly Concept

[+] Author and Article Information
Gracious Ngaile

Mem. ASME
North Carolina State University,
Department of Mechanical and
Aerospace Engineering,
911 Oval Drive, EB3,
Raleigh, NC 27695
e-mail: gngaile@ncsu.edu

James Lowrie

North Carolina State University,
Department of Mechanical and
Aerospace Engineering,
911 Oval Drive, EB3,
Raleigh, NC 27695
e-mail: jblowrie@ncsu.edu

Contributed by the Manufacturing Engineering Division of ASME for publication in the JOURNAL OF MICRO- AND NANO-MANUFACTURING. Manuscript received May 12, 2014; final manuscript received August 14, 2014; published online September 19, 2014. Assoc. Editor: Ulf Engel.

J. Micro Nano-Manuf 2(4), 041004 (Sep 19, 2014) (9 pages) Paper No: JMNM-14-1036; doi: 10.1115/1.4028320 History: Received May 12, 2014; Revised August 14, 2014

The advancement of micro tube hydroforming (THF) technology has been hindered by, among others, the lack of robust microdie systems that could facilitate hydroforming of complex parts that require both expansion and feeding. This paper proposes a new micro-THF die assembly that is based on floating a microdie-assembly in a pressurized chamber. The fluid pressure inside the chamber which surrounds the dies and punches is the same as the pressure required to hydroform the tube. The fluid pressure intensity in the chamber varies in accordance with the predetermined pressure loading path required to successfully hydroform the part. The system was built, and hydroforming experiments were carried out for various micro- and meso-scale shapes, including bulge-shapes, Y-shapes, and T-shapes.

Copyright © 2014 by ASME
Your Session has timed out. Please sign back in to continue.

References

Engel, U., 2006, “Tribology in Microforming,” Wear, 260, pp. 265–273. [CrossRef]
Ngaile, G., and Bunget, C., 2007, “Influence of Ultrasonic Vibration on Micro-Forming,” 2nd International Conference on Micro-Manufacturing, ICOMM, Clemson, SC, Sept. 10–13, pp. 46–51.
Qin, Y., 2010, “Overview on Micromanufacturing,” Micromanufacturing Engineering and Technology, Elsevier Science, Oxford, UK, pp. 1–23.
Parasız, S. A., Kinsey, B., Mahayotsanun, N., and Cao, J., 2007, “Dependence of Deformation on Grain Size and Sample Size in Microextrusion,” 2nd International Conference on Micromanufacturing, ICOMM, Clemson, SC, Sept. 10–13, pp. 52–56.
Geiger, M., Messner, A., and Engel, U., 1997, “Production of Microparts–Size Effects in Bulk Metal Forming, Similarity Theory,” Prod. Eng., 4, pp. 55–58.
Krishnan, N., Cao, J., Kinsey, B., Parasiz, S., and Li, M., 2005, “Investigation of Deformation Characteristics of Micropins Fabricated Using Microextrusions,” Proceedings of IMECE. [CrossRef]
Wulfsberg, J. P., and Terzi, M., 2005, “Investigation and Application of Size Effect Sin the Laser Assisted Forging of Microparts With Transparent Tools,” Proceedings of the 8th International Conference on Technology of Plasticity, Verona, Italy, Oct. 9–13.
Hartl, C., 2010, “Microhydroforming,” Micromanufacturing Engineering and Technology, Elsevier Science, Oxford, UK, pp. 146–161.
Sanchez-Salmeron, A. J., Lopez-Tarazon, R., Guzman-Diana, R., and Ricolfe-Viala, C., 2005, “Recent Development in Microhandling Systems for Micromanufacturing,” J. Mater. Process. Technol., 167(2–3), pp. 499–507. [CrossRef]
Krishnan, S., and Saggere, L., 2012, “Design and Development of a Novel Micro-Clasp Gripper for Micromanipulation of Complex-Shaped Objects,” Sens. Actuators, A, 176, pp. 110–123. [CrossRef]
Krie, M., 1999, “State of the Art of Sealing Techniques for Hydroforming Tools, Hydroforming of Tubes, Extrusions and Sheet Metals,” International Conference on Hydroforming, K. Siegert, ed., Felbach, Germany, pp. 441–461.
Bruce, S., George, T., and Daniel, E., 1993, “External Seal Unit for Tube Hydroforming,” U.S. Patent No. 5,233,856.
Mike, M., Terry, A., and George, T. W., 2007, “Hydroform Tube Sealing Assembly,” U.S. Patent No. 7,392,679.
Ngaile, G., 2013, “Development of MicroTube Hydroforming System,” Proceedings of the 8th International Conference on Micro-Manufacturing, Victoria, Canada, Mar. 25–28.
Gearing, D., and Mevissen, D., 2008, “Hydroforming Systems, Equipment, Control and Tooling,” Hydroforming for Advanced Manufacturing, Muammer Koc, ed., Woodhead Publishing Limited, Cambridge, UK, pp. 33–51.
Ngaile, G., and Yang, C., 2008, “Bulge Hydroforming of Micro Tubes for Fiber Optic Sensor Enclosures,” North Carolina State University, Technical Report No. THF/01.
Wagner, S. W., 2013, “Analysis of Non-Traditional Micro Tube Hydroforming Process,” Ph.D. dissertation, Michigan Technological University, UMI Dissertation Publications, Houghton Mifflin Harcourt, Boston, MA, pp. 1–160.
Wagner, S. W., Ng, K., Emblom, W. J., and Camelio, J. A., 2013, “Novel High Pressure Sealing System for Tube Hydroforming Operations,” ASME International Manufacturing Science and Engineering, Madison, WI, June 10–14. [CrossRef]
Ng, K., Wagner, S. W., Camelio, J. A., and Emblom, W. J., 2010, “Experimental Determination and Analysis of Flow Stress on Micro Tube Hydroforming Processes,” Trans. NAMRI/SME, 38, pp. 577–584.
Hartl, C., Anyasodor, G., Ptaschlik, T., Lungershausen, J., and Lippert, S., 2010, “Investigation Into Reduction of Die-Cavity Deflection in Micro-Hydroforming Processes Using FEA,” Int. J. Adv. Manuf. Technol., 47(9–12), pp. 853–858. [CrossRef]
Lungershausen, J., 2012, “Fundamental Studies on Tube Hydroforming and Laser Assistance in the Manufacture of Micro-Parts,” Ph.D. thesis, The University of Strathclyde, Glasgow, UK, pp. 1–218.
Hartl, C., Anyasodora, G., and Lungershausen, J., 2011, “Formability of Micro-Tubes in Hydroforming,” The 14th International ESAFORM Conference on Material Forming: ESAFORM 2011, AIP Conf. Proc., 1353, pp. 529–534.
Qin, Y., 2008, “MASMICRO Project Summary Report on Integration of Manufacturing Systems for Mass Manufacture of Miniature/Micro-Products,” http://cordis.europa.eu/documents/documentlibrary/126792231EN6.pdf

Figures

Grahic Jump Location
Fig. 1

Metallic seal variants [11]

Grahic Jump Location
Fig. 2

Elastomeric sealing system variants [11]

Grahic Jump Location
Fig. 3

Punch-tube-die junction in conventional macro-THF

Grahic Jump Location
Fig. 4

Decoupled punch-tube-die junction for expansion-driven micro-THF

Grahic Jump Location
Fig. 5

Decoupled punch-tube-die junction for feed-driven micro-THF

Grahic Jump Location
Fig. 6

Floating micro-THF die assembly and hydraulic fluid circuit schematic

Grahic Jump Location
Fig. 7

(a) Y-shape THF simulations: Strain distribution, (b) Y-shape THF simulations: Loading paths, and (c) Y-shape THF simulations: Punch load

Grahic Jump Location
Fig. 8

(a) T-shape THF simulations: Strain distribution, (b) T-shape THF simulations: Loading paths, and (c) T-shape THF simulations: Punch load

Grahic Jump Location
Fig. 9

(a) Bulge-shape THF simulations: Strain distribution, (b) bulge-shape THF simulations: Loading paths, and (c) bulge-shape THF simulations: Punch load

Grahic Jump Location
Fig. 10

Influence of friction and tube size on punch load

Grahic Jump Location
Fig. 11

Micro-THF floating die assembly setup

Grahic Jump Location
Fig. 12

1 mm and 2 mm die sets, notched punches, and punch cross section

Grahic Jump Location
Fig. 13

(a) A 150 ton hydraulic press and (b) 140 MPa pressure intensifier and control circuitry

Grahic Jump Location
Fig. 14 (a)

1 mm OD, L = 20 mm, feed = 1.0 mm and (b) 1 mm OD, L = 12 mm, feed 0.5 mm

Grahic Jump Location
Fig. 15

(a) Wrinkle formation and buckling, 2 mm OD, P = 100 MPa, feed = 2.0 mm and (b) loading path for parts shown in Fig. 15(a)

Grahic Jump Location
Fig. 16

2 mm OD, L = 12 mm, P = 100 MPa

Tables

Errata

Discussions

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In