0
Research Papers

Fabrication of Aluminum–SiC Laminate Nanocomposite by Ultrasonic Spray Deposited Sheet Bonding1

[+] Author and Article Information
Mina Bastwros

Mem. ASME
Department of Mechanical Engineering,
Iowa State University,
2034 H.M. Black Engineering,
Ames, IA 50011
e-mail: minamhb@iastate.edu

Gap-Yong Kim

Mem. ASME
Department of Mechanical Engineering,
Iowa State University,
2034 H.M. Black Engineering,
Ames, IA 50011
e-mail: gykim@iastate.edu

Paper presented at the 2014 ASME International Manufacturing Science and Engineering Conference (MSEC), Detroit, MI, June 9–13, 2014, Paper No. MSEC2014-3998.

2Corresponding author.

Contributed by the Manufacturing Engineering Division of ASME for publication in the JOURNAL OF MICRO- AND NANO-MANUFACTURING. Manuscript received October 19, 2014; final manuscript received May 27, 2015; published online June 25, 2015. Assoc. Editor: Don A. Lucca.

J. Micro Nano-Manuf 3(3), 031005 (Aug 01, 2015) (8 pages) Paper No: JMNM-14-1070; doi: 10.1115/1.4030705 History: Received October 19, 2014; Revised May 27, 2015; Online June 25, 2015

One of the challenges in making layered metal composites reinforced at interfaces has been controlling the dispersion and microstructure of the reinforcement particles. The reinforcement elements are typically applied at the interface by manual spreading using brush or by immersing the substrate in a suspension. In this study, an ultrasonic spraying technique has been used to deposit silicon carbide (SiC) nanoparticles on aluminum 6061 (Al6061) substrate foils to fabricate a laminate metal composite to control the deposited structure. The suspension parameters and the spraying parameters were investigated, and their influence on the deposited microstructure was analyzed. The laminate composite was consolidated using hot compaction, and a three-point bend test was performed to evaluate the mechanical properties. The yield and ultimate flexural strengths of the laminate composite reinforced with SiC nanoparticles increased by 32% and 15%, respectively, compared with those of the unreinforced sample prepared at the same condition.

Copyright © 2015 by ASME
Your Session has timed out. Please sign back in to continue.

References

Lee, S., Oyama, T., Wadsworth, J., and Sherby, O. D., 1992, “Impact Properties of a Laminated Composite Based on Ultrahigh Carbon Steel and Brass,” Mater. Sci. Eng. A, 154(2), pp. 133–137. [CrossRef]
Pozuelo, M., Carreño, F., and Ruano, O. A., 2006, “Delamination Effect on the Impact Toughness of an Ultrahigh Carbon–Mild Steel Laminate Composite,” Compos. Sci. Technol., 66(15), pp. 2671–2676. [CrossRef]
Hoffman, P. B., and Gibeling, J. C., 1995, “Near-Threshold Fatigue Crack Growth in Aluminum Composite Laminates,” Scr. Metall. Mater., 32(6), pp. 901–906. [CrossRef]
Lesuer, D. R., Syn, C. K., Sherby, O. D., Wadsworth, J., Lewandowski, J. J., and Hunt, W. H., 1996, “Mechanical Behaviour of Laminated Metal Composites,” Int. Mater. Rev., 41(5), pp. 169–197. [CrossRef]
Wang, H., Han, J., Du, S., and Northwood, D., 2007, “Reaction Synthesis of Nickel/Aluminide Multilayer Composites Using Ni and Al Foils: Microstructures, Tensile Properties, and Deformation Behavior,” Metall. Mater. Trans. A, 38(2), pp. 409–419. [CrossRef]
Samadzadeh, M., and Toroghinejad, M., 2014, “The Influence of Carbon Nanotube and Roll Bonding Parameters on the Bond Strength of Al Sheets,” J. Mater. Eng. Perform., 23(5), pp. 1887–1895. [CrossRef]
Rezayat, M., Akbarzadeh, A., and Owhadi, A., 2012, “Fabrication of High-Strength Al/Sic P Nanocomposite Sheets by Accumulative Roll Bonding,” Metall. Mater. Trans. A, 43(6), pp. 2085–2093. [CrossRef]
Schmidt, C. W., Knieke, C., Maier, V., Höppel, H. W., Peukert, W., and Göken, M., 2011, “Accelerated Grain Refinement During Accumulative Roll Bonding by Nanoparticle Reinforcement,” Scr. Mater., 64(3), pp. 245–248. [CrossRef]
Hao, L., Zhou, D., Fu, Q., and Hu, Y., 2013, “Multiferroic Properties of Multilayered BaTiO3–CoFe2O4 Composites Via Tape Casting Method,” J. Mater. Sci., 48(1), pp. 178–185. [CrossRef]
Hui, R., Wang, Z., Kesler, O., Rose, L., Jankovic, J., Yick, S., Maric, R., and Ghosh, D., 2007, “Thermal Plasma Spraying for SOFCs: Applications, Potential Advantages, and Challenges,” J. Power Sources, 170(2), pp. 308–323. [CrossRef]
Li, S.-R., Yesibolati, N., Qiao, Y., Ge, S.-Y., Feng, X.-Y., Zhu, J.-F., and Chen, C.-H., 2012, “Electrostatic Spray Deposition of Porous Fe2V4O13 Films as Electrodes for Li-Ion Batteries,” J. Alloys Compd., 520, pp. 77–82. [CrossRef]
Concina, I., Memarian, N., Selopal, G. S., Natile, M. M., Sberveglieri, G., and Vomiero, A., 2013, “Spray-Assisted Silar Deposition of Cadmium Sulphide Quantum Dots on Metal Oxide Films for Excitonic Solar Cells,” J. Power Sources, 240, pp. 736–744. [CrossRef]
Liu, L., Kim, G.-Y., and Chandra, A., 2010, “Fabrication of Solid Oxide Fuel Cell Anode Electrode by Spray Pyrolysis,” J. Power Sources, 195(20), pp. 7046–7053. [CrossRef]
Dobre, M., and Bolle, L., 2002, “Practical Design of Ultrasonic Spray Devices: Experimental Testing of Several Atomizer Geometries,” Exp. Therm. Fluid Sci., 26(2–4), pp. 205–211. [CrossRef]
Barua, B., and Saha, M. C., 2013, “Ultrasound Assisted Hybrid Carbon Epoxy Composites Containing Carbon Nanotubes,” ASME J. Eng. Mater. Technol., 135(1), p. 011009. [CrossRef]
Agashe, C., Takwale, M. G., Marathe, B. R., and Bhide, V. G., 1988, “Structural Properties of SnO2: F Films Deposited by Spray Pyrolysis,” Sol. Energy Mater., 17(2), pp. 99–117. [CrossRef]
Patil, P. S., 1999, “Versatility of Chemical Spray Pyrolysis Technique,” Mater. Chem. Phys., 59(3), pp. 185–198. [CrossRef]
Muecke, U. P., Messing, G. L., and Gauckler, L. J., 2009, “The Leidenfrost Effect During Spray Pyrolysis of Nickel Oxide-Gadolinia Doped Ceria Composite Thin Films,” Thin Solid Films, 517(5), pp. 1515–1521. [CrossRef]
Ely, F., Matsumoto, A., Zoetebier, B., Peressinotto, V. S., Hirata, M. K., De Sousa, D. A., and Maciel, R., 2014, “Handheld and Automated Ultrasonic Spray Deposition of Conductive PEDOT:PSS Films and Their Application in AC EL Devices,” Org. Electron., 15(5), pp. 1062–1070. [CrossRef]
Liu, L., Kim, G.-Y., Hillier, A. C., and Chandra, A., 2011, “Microstructural and Electrochemical Impedance Study of Nickel–Ce0.9Gd0.1O1.95 Anodes for Solid Oxide Fuel Cells Fabricated by Ultrasonic Spray Pyrolysis,” J. Power Sources, 196(6), pp. 3026–3032. [CrossRef]
Valdés, M., Santoro, G., and Vázquez, M., 2014, “Spray Deposition of Cu2ZnSnS4 Thin Films,” J. Alloys Compd., 585, pp. 776–782. [CrossRef]
Yao, J., He, Y., Wang, D., and Lin, J., 2014, “High-Temperature Oxidation Resistance of (Al2O3–Y2O3)/(Y2O3-Stabilized ZrO2) Laminated Coating on 8Nb–TiAl Alloy Prepared by a Novel Spray Pyrolysis,” Corros. Sci., 80, pp. 19–27. [CrossRef]
Jung, C.-H., Yun, J., Qadir, K., Naik, B., Yun, J.-Y., and Park, J. Y., 2014, “Catalytic Activity of Pt/SiO2 Nanocatalysts Synthesized Via Ultrasonic Spray Pyrolysis Process Under Co Oxidation,” Appl. Catal. B, 154–155, pp. 171–176. [CrossRef]
Li, C.-P., Lin, F., Richards, R. M., Engtrakul, C., Tenent, R. C., and Wolden, C. A., 2014, “The Influence of Sol–Gel Processing on the Electrochromic Properties of Mesoporous Wo3 Films Produced by Ultrasonic Spray Deposition,” Sol. Energy Mater. Sol. Cells, 121, pp. 163–170. [CrossRef]
Das, S. K., Choi, S. U. S., and Patel, H. E., 2006, “Heat Transfer in Nanofluids—A Review,” Heat Transfer Eng., 27(10), pp. 3–19. [CrossRef]
Jones, M., Li, C., Afjeh, A., and Peterson, G., 2011, “Experimental Study of Combustion Characteristics of Nanoscale Metal and Metal Oxide Additives in Biofuel (Ethanol),” Nanoscale Res. Lett., 6(1), p. 246. [CrossRef] [PubMed]
Sridhara, V., and Satapathy, L., 2011, “Al2O3-Based Nanofluids: A Review,” Nanoscale Res. Lett., 6(1), pp. 1–16. [CrossRef]
Willey, A. D., Holt, J. M., Larsen, B. A., Blackburn, J. L., Liddiard, S., Abbott, J., Coffin, M., Vanfleet, R. R., and Davis, R. C., 2014, “Thin Films of Carbon Nanotubes Via Ultrasonic Spraying of Suspensions in N-Methyl-2-Pyrrolidone and N-Cyclohexyl-2-Pyrrolidone,” J. Vac. Sci. Technol. B, 32(1), p. 011218. [CrossRef]
Dobre, M., and Bolle, L., 1999, “Visualisation and Analysis of Liquid Film Surface Patterns Formed on Ultrasonic Atomisers,” Proceedings of the 15th ILASS-Europe, Toulouse, France, pp. 1–6.
Wilhelm, O., Pratsinis, S. E., Perednis, D., and Gauckler, L. J., 2005, “Electrospray and Pressurized Spray Deposition of Yttria-Stabilized Zirconia Films,” Thin Solid Films, 479(1–2), pp. 121–129. [CrossRef]
Reolon, R. P., Halmenschlager, C. M., Neagu, R., De Fraga Malfatti, C., and Bergmann, C. P., 2014, “Electrochemical Performance of Gadolinia-Doped Ceria (CGO) Electrolyte Thin Films for ITSOFC Deposited by Spray Pyrolysis,” J. Power Sources, 261, pp. 348–355. [CrossRef]
Zhu, D. S., Wu, S. Y., and Wang, N., 2010, “Surface Tension and Viscosity of Aluminum Oxide Nanofluids,” AIP Conf. Proc., 1207(1), pp. 460–464. [CrossRef]
Kumar, R., and Milanova, D., 2009, “Effect of Surface Tension on Nanotube Nanofluids,” Appl. Phys. Lett., 94(7), p. 073107. [CrossRef]
Tanvir, S., and Qiao, L., 2012, “Surface Tension of Nanofluid-Type Fuels Containing Suspended Nanomaterials,” Nanoscale Res. Lett., 7(1), pp. 1–10. [CrossRef] [PubMed]
Saeid, V., Arup, P., Abhishek, J., Ganapathiraman, R., and Theodorian, B.-T., 2009, “The Effect of Nanoparticles on the Liquid–Gas Surface Tension of Bi2Te3 Nanofluids,” Nanotechnology, 20(18), p. 185702. [CrossRef] [PubMed]
Modesto-López, L. B., Miettinen, M., Torvela, T., Lähde, A., and Jokiniemi, J., 2015, “Direct Deposition of Graphene Nanomaterial Films on Polymer-Coated Glass by Ultrasonic Spraying,” Thin Solid Films, 578, pp. 45–52. [CrossRef]
Nandiyanto, A. B. D., and Okuyama, K., 2011, “Progress in Developing Spray-Drying Methods for the Production of Controlled Morphology Particles: From the Nanometer to Submicrometer Size Ranges,” Adv. Powder Technol., 22(1), pp. 1–19. [CrossRef]
Muecke, U. P., Luechinger, N., Schlagenhauf, L., and Gauckler, L. J., 2009, “Initial Stages of Deposition and Film Formation During Spray Pyrolysis—Nickel Oxide, Cerium Gadolinium Oxide and Mixtures Thereof,” Thin Solid Films, 517(5), pp. 1522–1529. [CrossRef]
Perednis, D., and Gauckler, L., 2005, “Thin Film Deposition Using Spray Pyrolysis,” J. Electroceram., 14(2), pp. 103–111. [CrossRef]
Radiom, M., Yang, C., and Chan, W. K., 2009, “Characterization of Surface Tension and Contact Angle of Nanofluids,” Proc SPIE, 7522, p. 75221D. [CrossRef]
Chen, R.-H., Phuoc, T. X., and Martello, D., 2011, “Surface Tension of Evaporating Nanofluid Droplets,” Int. J. Heat Mass Transfer, 54(11–12), pp. 2459–2466. [CrossRef]
Kim, J.-K., Jung, J. Y., and Kang, Y. T., 2006, “The Effect of Nano-Particles on the Bubble Absorption Performance in a Binary Nanofluid,” Int. J. Refrig., 29(1), pp. 22–29. [CrossRef]
Veleva, L., Schaeublin, R., Battabyal, M., Plociski, T., and Baluc, N., 2015, “Investigation of Microstructure and Mechanical Properties of W–Y and W–Y2O3 Materials Fabricated by Powder Metallurgy Method,” Int. J. Refract. Metals Hard Mater., 50, pp. 210–216. [CrossRef]
Fang, X., Jia, J., and Feng, X., 2015, “Three-Point Bending Test at Extremely High Temperature Enhanced by Real-Time Observation and Measurement,” Measurement, 59, pp. 171–176. [CrossRef]
Tohgo, K., Fujii, T., Harada, M., Isono, H., and Shimamura, Y., 2015, “Fabrication of PSZ–Ti Composites by Spark Plasma Sintering and Their Mechanical Properties,” Mater. Sci. Eng. A, 621, pp. 166–172. [CrossRef]
Wu, Y., Kim, G.-Y., and Russell, A. M., 2012, “Effects of Mechanical Alloying on an Al6061–CNT Composite Fabricated by Semi-Solid Powder Processing,” Mater. Sci. Eng. A, 538, pp. 164–172. [CrossRef]
Jokanović, V., Janaćković, D., and Uskoković, D., 1999, “Influence of Aerosol Formation Mechanism by an Ultrasonic Field on Particle Size Distribution of Ceramic Powders,” Ultrason. Sonochem., 6(3), pp. 157–169. [CrossRef]
Hsieh, Y.-P., Hofmann, M., Son, H., Jia, X., Chen, Y.-F., Liang, C.-T., Dresselhaus, M. S., and Kong, J., 2009, “Direct Deposition of Single-Walled Carbon Nanotube Thin Films Via Electrostatic Spray Assisted Chemical Vapor Deposition,” Nanotechnology, 20(6), p. 065601. [CrossRef] [PubMed]
Naoki, O., Yeong, Y., and Isobel, D., 2007, “Fabrication of Gas Electrodes by Wet Powder Spraying of Binder-Free Particle Suspensions Using a Pulse Injection Process,” J. Am. Ceram. Soc., 90(5), pp. 1365–1369. [CrossRef]
Wu, Y., and Kim, G.-Y., 2011, “Carbon Nanotube Reinforced Aluminum Composite Fabricated by Semi-Solid Powder Processing,” J. Mater. Process. Technol., 211(8), pp. 1341–1347. [CrossRef]
Esawi, A., and Morsi, K., 2007, “Dispersion of Carbon Nanotubes (CNTs) in Aluminum Powder,” Composites Part A, 38(2), pp. 646–650. [CrossRef]

Figures

Grahic Jump Location
Fig. 1

Ultrasonic spray deposition system

Grahic Jump Location
Fig. 2

Overview of the spraying process

Grahic Jump Location
Fig. 3

Experimental setup for semisolid powder processing

Grahic Jump Location
Fig. 4

The effect of SiC loading and particle size on the surface tension of ethanol–SiC suspension system

Grahic Jump Location
Fig. 5

Prediction of the droplet size from the atomization

Grahic Jump Location
Fig. 6

Prediction of the droplet size from the atomization using different atomization frequencies

Grahic Jump Location
Fig. 7

Single droplets deposited by single spray pass

Grahic Jump Location
Fig. 15

SEM images of reinforcement layer on the fracture surfaces of (a) Al6061–0.3 wt. % SiC composite and (b) Al6061–0.6 wt. % SiC composite

Grahic Jump Location
Fig. 14

SEM images of Al6061 layer on the fracture surfaces of (a) Al6061–0.3 wt. % SiC composite and (b) Al6061–0.6 wt. % SiC composite

Grahic Jump Location
Fig. 13

SEM images of SiC reinforcement layer on the fracture surfaces of (a) Al6061–0.3 wt. % SiC composite and (b) Al6061–0.6 wt. % SiC composite

Grahic Jump Location
Fig. 12

Effect of SiC loading on the flexural stress–strain curves

Grahic Jump Location
Fig. 11

Effect of spraying distance change on the deposition structure with spraying condition at T = 300 °C, Q = 0.24 ml/min, and P = 0.24 kPa

Grahic Jump Location
Fig. 10

Effect of air pressure change on the deposition structure with spraying condition at T = 300 °C, Q = 0.24 ml/min, and D = 25 mm

Grahic Jump Location
Fig. 9

Effect of temperature change on the deposition structure with spraying condition at Q = 0.25 ml/min, D = 25 mm, and P = 0.24 kPa

Grahic Jump Location
Fig. 8

Effect of flow rate change on the deposition structure with spraying condition at T = 300 °C, D = 25 mm, and P = 0.24 kPa

Tables

Errata

Discussions

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In