0
Research Papers

Three-Dimensional Printing of Nanoscale Powders Using Laser Shockwaves

[+] Author and Article Information
P. A. Molian

Department of Mechanical and
Manufacturing Engineering,
St. Cloud State University,
St. Cloud, MN 56301
e-mail: pamolian@stcloudstate.edu

Contributed by the Manufacturing Engineering Division of ASME for publication in the JOURNAL OF MICRO- AND NANO-MANUFACTURING. Manuscript received June 26, 2015; final manuscript received August 23, 2015; published online September 22, 2015. Assoc. Editor: Bin Wei.

J. Micro Nano-Manuf 3(4), 041006 (Sep 22, 2015) (10 pages) Paper No: JMNM-15-1039; doi: 10.1115/1.4031462 History: Received June 26, 2015; Revised August 23, 2015

A new three-dimensional (3D) printing process designated as shockwave-induced freeform technique (SWIFT) is explored for fabricating microparts from nanopowders. SWIFT consists of generating shockwaves using a laser beam, applying these shocks to pressure sinter nanoparticles at room temperature, and creating structures and devices by the traditional layer-by-layer formation. Shockwave cold compaction of nanoscale powders has the capability to overcome limitations, such as shrinkage, porosity, rough surface, and wide tolerance, normally encountered in hot sintering processes, such as selective laser sintering. In this study, the window of operating parameters and the underlying physics of SWIFT were investigated using a high-energy Q-switched Nd: YAG laser and nanodiamond (ND) powders. Results indicate the potential of SWIFT for fabricating high-performance diamond microtools with high aspect ratios, smooth surfaces, and sharp edges. The drawback is that the SWIFT process does not work for micro-sized powders.

Copyright © 2015 by ASME
Your Session has timed out. Please sign back in to continue.

References

Figures

Grahic Jump Location
Fig. 1

Schematic experimental setup for the generation of laser shockwaves

Grahic Jump Location
Fig. 2

Schematic of nanoparticle fluidization setup

Grahic Jump Location
Fig. 3

Schematic of SWIFT process where nanoparticles are fed to the chamber through fluidized bed and then subjected to laser shockwaves

Grahic Jump Location
Fig. 4

Single-pulse shockwave sintering effects (a) Sintered zone and (b) surface morphology

Grahic Jump Location
Fig. 5

Effect of multiple shocks: (a) one (0.4 W, 1 Hz) and (b) five (2 W, 5 Hz)

Grahic Jump Location
Fig. 6

Multiple shocks (ten) layer processed using 4 W, 10 Hz

Grahic Jump Location
Fig. 7

Laser shock sintered 3D part for a thickness of 250 μm

Grahic Jump Location
Fig. 8

Hardness of laser shock sintered ND

Grahic Jump Location
Fig. 9

Micromotor pattern generated by the SWIFT process

Grahic Jump Location
Fig. 10

Raman spectrum of unshocked raw powder of ND

Grahic Jump Location
Fig. 11

Raman spectra of various regions in laser shocked ND sample

Grahic Jump Location
Fig. 12

Phase diagram of nanocarbon [31]

Grahic Jump Location
Fig. 13

Schematic of the domain design to study ND particle phase change and binding under external pressing

Grahic Jump Location
Fig. 14

Initial atomic configuration. The red dots represent the copper atoms and blue ones stand for diamond. Laser irradiated copper cube in negative z direction. Diamond particles (comprising of one full and two half particles) is of radius 2.85 nm in x–y plane. Copper is 9.94 nm in z direction and 2.85 nm in x direction. Diamond and copper are of 0.889 nm thickness in the y direction. The gap between copper and diamond is set to be 1 nm.

Grahic Jump Location
Fig. 15

Radial distribution function for diamond: (a) At t = 5 fs, both long-range and short-range peak are visible and (b) however, when it comes to 40 ps, long-range peaks disappear

Grahic Jump Location
Fig. 16

The change in nearest atomic distance. From 38 ps to 40 ps, the nearest atomic distance drops from 1.55 Å to 1.45 Å.

Tables

Errata

Discussions

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In