0
Technical Brief

A Novel Hybrid Heating Method for Mechanical Testing of Miniature Specimens at Elevated Temperature

[+] Author and Article Information
Lin Li

Department of Mechanical and Aerospace Engineering,
North Carolina State University,
Raleigh, NC 27695-7910
e-mail: lli24@ncsu.edu

Gracious Ngaile

Mem. ASME
Department of Mechanical and Aerospace Engineering,
North Carolina State University,
Raleigh, NC 27695-7910
e-mail: gngaile@ncsue.du

Tasnim Hassan

Department of Civil, Construction, and
Environmental Engineering,
North Carolina State University,
Raleigh, NC 27695-7908
e-mail: thassan@ncsu.edu

Contributed by the Manufacturing Engineering Division of ASME for publication in the JOURNAL OF MICRO- AND NANO-MANUFACTURING. Manuscript received September 16, 2016; final manuscript received February 3, 2017; published online March 23, 2017. Editor: Jian Cao.

J. Micro Nano-Manuf 5(2), 024501 (Mar 23, 2017) (5 pages) Paper No: JMNM-16-1045; doi: 10.1115/1.4035954 History: Received September 16, 2016; Revised February 03, 2017

A novel hybrid heating method which combines the conventional electric-resistance specimen heating with microcoil heating of specimen ends to achieve uniform heating over the gauge length is presented. Resistive heating of a miniature specimen develops a parabolic temperature profile with lowest temperature at the grip ends because of the heat loss to the gripper. Coil heating at the specimen ends compensates for this heat loss resulting in uniform temperature distribution over the central segment of the specimen. Thermo-electric finite element simulations were carried out to analyze the transient and steady temperature distribution in miniature specimens followed by experimental validation.

FIGURES IN THIS ARTICLE
<>
Copyright © 2017 by ASME
Your Session has timed out. Please sign back in to continue.

References

Lord, J. D. , Roebuck, B. , Morrell, R. , and Lube, T. , 2010, “ Aspects of Strain and Strength Measurement in Miniaturized Testing for Engineering Metals and Ceramics,” Mater. Sci. Technol., 26(2), pp. 127–148. [CrossRef]
Jaya, B. N. , and Alam, M. Z. , 2013, “ Small-Scale Mechanical Testing of Materials,” Curr. Sci., 105(8), pp. 1073–1099.
Lucas, G. E. , 1983, “ The Development of Small Specimen Mechanical Tests Techniques,” J. Nucl. Mater., 117, pp. 327–339. [CrossRef]
Hyde, T. H. , Sun, W. , and Williams, J. A. , 2007, “ Requirements for and Use of a Miniature Test Specimens to Provide Mechanical and Creep Properties of Materials: A Review,” Int. Mater. Rev., 52(4), pp. 213–255. [CrossRef]
Lucas, G. E. , 1990, “ Review of Small Specimen Test Techniques for Irradiation Testing,” Metall. Trans. A, 21(5), pp. 1105–1119. [CrossRef]
Lucas, G. E. , Odette, G. R. , Matsui, H. , Moslang, A. , Spatig, P. , Rensman, J. , and Yamamoto, T. , 2007, “ The Role of Small Specimen Tests Technology in Fusion Materials Development,” J. Nucl. Mater., 367–370(Part B), pp. 1549–1556. [CrossRef]
Wakai, E. , Nogami, S. , Kasada, R. , Kimura, A. , Kurishita, H. , Saito, M. , Ito, Y. , Takada, F. , Nakamura, K. , Molla, J. , and Garin, P. , 2011, “ Small Specimen Test Technology and Methodology of IFMIF/EVEDA and the Further Subjects,” J. Nucl. Mater., 417(1–3), pp. 1325–1330. [CrossRef]
Razali, A. R. , and Qin, Y. , 2013, “ A Review on Micro-Manufacturing, Micro-Forming and Their Key Issues,” Procedia Eng., 53, pp. 665–672. [CrossRef]
Eichehueller, B. , 2007, “ Microforming at Elevated Temperature Forming and Material Behavior,” Int. J. Adv. Manuf. Technol., 33(1), pp. 119–124. [CrossRef]
Geiger, M. , Kleiner, M. , Eckstein, R. , Tiesler, N. , and Engel, U. , 2001, “ Microforming,” CIRP Ann.—Manuf. Technol., 50(2), pp. 445–462. [CrossRef]
Fu, M. W. , and Chan, W. L. , 2014, Micro-Scales Products Developments Via Microforming (Springer Series in Advanced Manufacturing), Springer-Verlag, London, pp. 9–41.
Czoboly, E. , Gillemot, F. , and Oszwald, F. , 1998, “ Small Specimen Testing Applied at Surveillance Extension,” Small Specimen Test Techniques, ASTM, Philadelphia, PA, pp. 163–172, Standard No. STP 1329.
Hankin, G. L. , Toloczko, M. B. , Hamilton, M. L. , Garner, F. A. , and Faulkner, R. G. , 1998, “ Validation of the Shear Punch-Tensile Correlation Technique Using Irradiated Materials,” J. Nucl. Mater., 258–263(Part 2), pp. 1651–1656. [CrossRef]
Nedoushan, R. J. , Farzin, M. , and Banabic, D. , 2014, “ Simulation of Hot Forming Process: Using Cost Effective Micro-Structural Constitutive Models,” Int. J. Mech. Sci., 85, pp. 196–204. [CrossRef]
Haque, M. A. , and Saif, M. T. , 2004, “ Deformation Mechanisms in Free-Standing Nanoscale Thin Films: A Quantitative In Situ Transmission Electron Microscope Study,” PNAS, 101(17), pp. 6335–6340. [CrossRef] [PubMed]
Ma, X. , and Shi, H. , 2014, “ In Situ SEM Studies of the Low Cycle Fatigue Behavior of DZ4 Superalloy at Elevated Temperature: Effect of Partial Recrystallization,” Int. J. Fatigue, 61, pp. 255–263. [CrossRef]
Guo, E. Y. , Wang, M. Y. , Jing, T. , and Chawla, N. , 2013, “ Temperature-Dependent Mechanical Properties of an Austenitic–Ferritic Stainless Steel Studied by In Situ Tensile Loading in a Scanning Electron Microscope,” Mater. Sci. Eng. A, 580, pp. 159–168. [CrossRef]
Petrenec, M. , Polák, J. , Šamořil, M. , Dluhoš, J. , and Obrtlík, K. , 2014, “ In-Situ Study of the Mechanisms of High Temperature Damage in Elastic-Plastic Cyclic Loading of Nickel Superalloy,” Adv. Mater. Res., 891–892, pp. 530–535. [CrossRef]
Petrenec, M. , Polák, J. , Šamořil, M. , Dluhoš, J. , and Obrtlík, K. , 2014, “ In-Situ High Temperature Low Cycle Fatigue Study of Surface Topography Evolution in Nickel Superalloy,” 23rd International Conference on Metallurgy and Materials (METAL), Brno, Czech Republic, May 21–23.
Callaghan, M. D. , Humphries, S. R. , Law, M. , Li, H. , and Yeung, W. Y. , 2010, “ Evaluation of High Temperature Fatigue Behavior of P22 by Miniature Specimen Testing,” Mater. Sci. Forum, 638–642, pp. 3937–3942. [CrossRef]
Kohyama, A. , Sato, S. , and Hamada, K. , 1993, “ An Automated Tensile Machine for Small Specimens Heavily Neutron Irradiated in FFTF/MOTA,” Small Specimen Test Techniques Applied to Nuclear Reactor Vessels Thermal Annealing and Plant Life Extension, W. R. Corwin , F. M. Haggag , and W. L. Server , eds., American Society for Testing and Materials, Philadelphia, PA, pp. 356–367.
Hannula, S. P. , Wanagel, J. , and Li, C. Y. , 1986, “ A Miniaturized Mechanical Testing System for Small-Scale Specimen Testing,” The Use of Small-Scale Specimens for Testing Irradiated Material, W. R. Corwin and G. E. Lucas , eds., American Society for Testing and Materials, Philadelphia, PA, pp. 233–251.
Quested, T. E. , 2000, “ Finite Element Analysis of Miniaturised Electro Thermo Mechanical Testing System,” NPL Report CMMT (A) No. 291.
Ho, C. Y. , and Chu, T. K. , 1977, “ Electric Resistivity and Thermal Conductivity of Nine Selected AISI Stainless Steels,” U.S. Defense Technical Information Center, Defense Logistics Agency, Alexandria, VA, CINDAS Report No. 45, pp. 5–30.

Figures

Grahic Jump Location
Fig. 1

The resistive, coil, and hybrid heating methods, (a) and (b) the grippers and specimen, (c) current input for coil heating, resistive heating, and hybrid heating

Grahic Jump Location
Fig. 2

Electric-resistance heating temperature distributions for different specimen lengths

Grahic Jump Location
Fig. 3

Transient and steady temperature distributions of a 6-mm specimen by coil heating

Grahic Jump Location
Fig. 4

The steady temperature distribution by coil heating for different specimen lengths

Grahic Jump Location
Fig. 5

The temperature distributions in a 6-mm-long specimen by three different heating methods

Grahic Jump Location
Fig. 6

The temperature distributions in a 50-mm-long specimen by three different heating methods

Grahic Jump Location
Fig. 7

The experiment setup for validation of the novel hybrid heating technique

Grahic Jump Location
Fig. 8

Temperature distribution for a 10-mm-long specimen by (a) resistance heating and (b) specimen end coil heating

Grahic Jump Location
Fig. 9

Temperature distribution for a 10-mm-long specimen by hybrid heating

Tables

Errata

Discussions

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In