There is considerable interest in computational and experimental flow investigations within abdominal aortic aneurysms (AAAs). This task stipulates advanced grid generation techniques and cross-validation because of the anatomical complexity. The purpose of this study is to examine the feasibility of velocity measurements by particle tracking velocimetry (PTV) in realistic AAA models. Computed tomography and rapid prototyping were combined to digitize and construct a silicone replica of a patient-specific AAA. Three-dimensional velocity measurements were acquired using PTV under steady averaged resting boundary conditions. Computational fluid dynamics (CFD) simulations were subsequently carried out with identical boundary conditions. The computational grid was created by splitting the luminal volume into manifold and nonmanifold subsections. They were filled with tetrahedral and hexahedral elements, respectively. Grid independency was tested on three successively refined meshes. Velocity differences of about 1% in all three directions existed mainly within the AAA sack. Pressure revealed similar variations, with the sparser mesh predicting larger values. PTV velocity measurements were taken along the abdominal aorta and showed good agreement with the numerical data. The results within the aneurysm neck and sack showed average velocity variations of about 5% of the mean inlet velocity. The corresponding average differences increased for all velocity components downstream the iliac bifurcation to as much as 15%. The two domains differed slightly due to flow-induced forces acting on the silicone model. Velocity quantification through narrow branches was problematic due to decreased signal to noise ratio at the larger local velocities. Computational wall pressure and shear fields are also presented. The agreement between CFD simulations and the PTV experimental data was confirmed by three-dimensional velocity comparisons at several locations within the investigated AAA anatomy indicating the feasibility of this approach.
1.
Kleinstreuer
, C.
, and Li
, Z.
, 2006, “Analysis and Computer Program for Rupture-Risk Prediction of Abdominal Aortic Aneurysms
,” Biomed. Eng. Online
1475-925X, 5
:19.2.
Kleinstreuer
, C.
, Hyun
, S.
, Buchanan
, J. R.
, Longest
, P. W.
, Archie
, J. P.
, and Truskey
, G. A.
, 2001, “Hemodynamic Parameters and Early Intimal Thickening in Branching Blood Vessels
,” Crit. Rev. Biomed. Eng.
0278-940X, 29
(1
), pp. 1
–64
.3.
Thubrikar
, M. J.
, Al-Soudi
, J.
, and Robicsek
, F.
, 2001, “Wall Stress Studies of Abdominal Aortic Aneurysm in a Clinical Model
,” Ann. Vasc. Surg.
0890-5096, 15
(3
), pp. 355
–366
.4.
Giddens
, D. P.
, Zarins
, C. K.
, and Glagov
, S.
, 1993, “The Role of Fluid-Mechanics in the Localization and Detection of Atherosclerosis
,” ASME J. Biomech. Eng.
0148-0731, 115
(4
), pp. 588
–594
.5.
Bonert
, M.
, Leask
, R. L.
, Butany
, J.
, Ethier
, C. R.
, Myers
, J. G.
, Johnston
, K. W.
, and Ojha
, M.
, 2003, “The Relationship Between Wall Shear Stress Distributions and Intimal Thickening in the Human Abdominal Aorta
,” Biomed. Eng. Online
1475-925X, 2
:18.6.
Lee
, D.
, and Chen
, J. Y.
, 2002, “Numerical Simulation of Steady Flow Fields in a Model of Abdominal Aorta With Its Peripheral Branches
,” J. Biomech.
0021-9290, 35
(8
), pp. 1115
–1122
.7.
Taylor
, C. A.
, Hughes
, T. J. R.
, and Zarins
, C. K.
, 1998, “Finite Element Modeling of Three-Dimensional Pulsatile Flow in the Abdominal Aorta: Relevance to Atherosclerosis
,” Ann. Biomed. Eng.
0090-6964, 26
(6
), pp. 975
–987
.8.
Taylor
, C. A.
, Hughes
, T. J. R.
, and Zarins
, C. K.
, 1999, “Effect of Exercise on Hemodynamic Conditions in the Abdominal Aorta
,” J. Vasc. Surg.
0741-5214, 29
(6
), pp. 1077
–1089
.9.
Ku
, D. N.
, Glagov
, S.
, Moore
, J. E.
, and Zarins
, C. K.
, 1989, “Flow Patterns in the Abdominal-Aorta Under Simulated Postprandial and Exercise Conditions—An Experimental-Study
,” J. Vasc. Surg.
0741-5214, 9
(2
), pp. 309
–316
.10.
Moore
, J. E.
, Ku
, D. N.
, Zarins
, C. K.
, and Glagov
, S.
, 1992, “Pulsatile Flow Visualization in the Abdominal-Aorta Under Differing Physiological Conditions-Implications for Increased Susceptibility to Atherosclerosis
,” ASME J. Biomech. Eng.
0148-0731, 114
(3
), pp. 391
–397
.11.
Pedersen
, E. M.
, Yoganathan
, A. P.
, and Lefebvre
, X. P.
, 1992, “Pulsatile Flow Visualization in a Model of the Human Abdominal-Aorta and Aortic Bifurcation
,” J. Biomech.
0021-9290, 25
(8
), pp. 935
–944
.12.
Pedersen
, E. M.
, Sung
, H. W.
, Burlson
, A. C.
, and Yoganathan
, A. P.
, 1993, “2-Dimensional Velocity-Measurements in a Pulsatile Flow Model of the Normal Abdominal-Aorta Simulating Different Hemodynamic Conditions
,” J. Biomech.
0021-9290, 26
, pp. 1237
–1247
.13.
Boesiger
, P.
, Maier
, S. E.
, Liu
, K. C.
, Scheidegger
, M. B.
, and Meier
, D.
, 1992, “Visualization and Quantification of the Human Blood-Flow by Magnetic-Resonance-Imaging
,” J. Biomech.
0021-9290, 25
(1
), pp. 55
–67
.14.
Moore
, J. E.
, and Ku
, D. N.
, 1994, “Pulsatile Velocity-Measurements in a Model of the Human Abdominal-Aorta Under Resting Conditions
,” ASME J. Biomech. Eng.
0148-0731, 116
(3
), pp. 337
–346
.15.
Moore
, J. E.
, and Ku
, D. N.
, 1994, “Pulsatile Velocity-Measurements in a Model of the Human Abdominal-Aorta Under Simulated Exercise and Postprandial Conditions
,” ASME J. Biomech. Eng.
0148-0731, 116
(1
), pp. 107
–111
.16.
Moore
, J. E.
, Maier
, S. E.
, Ku
, D. N.
, and Boesiger
, P.
, 1994, “Hemodynamics in the Abdominal-Aorta—A Comparison of In-Vitro and In-Vivo Measurements
,” J. Appl. Physiol.
8750-7587, 76
(4
), pp. 1520
–1527
.17.
Taylor
, T. W.
, and Yamaguchi
, T.
, 1994, “3-Dimensional Simulation of Blood-Flow in an Abdominal Aortic-Aneurysm—Steady and Unsteady-Flow Cases
,” ASME J. Biomech. Eng.
0148-0731, 116
(1
), pp. 89
–97
.18.
Finol
, E. A.
, and Amon
, C. H.
, 2001, “Blood Flow in Abdominal Aortic Aneurysms: Pulsatile Flow Hemodynamics
,” ASME J. Biomech. Eng.
0148-0731, 123
(5
), pp. 474
–484
.19.
Finol
, E. A.
, Keyhani
, K.
, and Amon
, C. H.
, 2003, “The Effect of Asymmetry in Abdominal Aortic Aneurysms Under Physiologically Realistic Pulsatile Flow Conditions
,” ASME J. Biomech. Eng.
0148-0731, 125
(2
), pp. 207
–217
.20.
Kumar
, B. V. R.
, 2003, “A Space-Time Analysis of Blood Flow in a 3D Vessel With Multiple Aneurysms
,” Comput. Mech.
0178-7675, 32
(1–2
), pp. 16
–28
.21.
Fukushima
, T.
, Matsuzawa
, T.
, and Homma
, T.
, 1989, “Visualization and Finite-Element Analysis of Pulsatile Flow in Models of the Abdominal Aortic-Aneurysm
,” Biorheology
0006-355X, 26
(2
), pp. 109
–130
.22.
Asbury
, C. L.
, Ruberti
, J. W.
, Bluth
, E. I.
, and Peattie
, R. A.
, 1995, “Experimental Investigation of Steady Flow in Rigid Models of Abdominal Aortic-Aneurysms
,” Ann. Biomed. Eng.
0090-6964, 23
(1
), pp. 29
–39
.23.
Egelhoff
, C. J.
, Budwig
, R. S.
, Elger
, D. F.
, Khraishi
, T. A.
, and Johansen
, K. H.
, 1999, “Model Studies of the Flow in Abdominal Aortic Aneurysms During Resting and Exercise Conditions
,” J. Biomech.
0021-9290, 32
(12
), pp. 1319
–1329
.24.
Peattie
, R. A.
, Riehle
, T. J.
, and Bluth
, E. I.
, 2004, “Pulsatile Flow in Fusiform Models of Abdominal Aortic Aneurysms: Flow Fields, Velocity Patterns and Flow-Induced Wall Stresses
,” ASME J. Biomech. Eng.
0148-0731, 126
(4
), pp. 438
–446
.25.
Bluestein
, D.
, Niu
, L.
, Schoephoerster
, R. T.
, and Dewanjee
, M. K.
, 1996, “Steady Flow in an Aneurysm Model: Correlation Between Fluid Dynamics and Blood Platelet Deposition
,” ASME J. Biomech. Eng.
0148-0731, 118
(3
), pp. 280
–286
.26.
Yu
, S. C. M.
, Chan
, W. K.
, Ng
, B. T. H.
, and Chua
, L. P.
, 1999, “A Numerical Investigation on the Steady and Pulsatile Flow Characteristics in Axi-Symmetric Abdominal Aortic Aneurysm Models With Some Experimental Evaluation
,” J. Med. Eng. Technol.
0309-1902, 23
(6
), pp. 228
–239
.27.
Boutsianis
, E.
, Frauenfelder
, T.
, Wildermuth
, S.
, Poulikakos
, D.
, and Ventikos
, Y.
, 2003, “Anatomically Accurate Haemodynamic Simulations of Abdominal Aortic Aneurysms
,” 2003 Advances in Bioengineering
, Washington, DC
, paper No. IMECE2003-42766, pp. 61
–62
.28.
Fillinger
, M. F.
, Raghavan
, M. L.
, Marra
, S. P.
, Cronenwett
, J. L.
, and Kennedy
, F. E.
, 2002, “In Vivo Analysis of Mechanical Wall Stress and Abdominal Aortic Aneurysm Rupture Risk
,” J. Vasc. Surg.
0741-5214, 36
(3
), pp. 589
–597
.29.
Scotti
, C. M.
, and Finol
, E. A.
, 2007, “Compliant Biomechanics of Abdominal Aortic Aneurysms: A Fluid-Structure Interaction Study
,” Comput. Struct.
0045-7949, 85
(11–14
), pp. 1097
–1113
.30.
Wolters
, B. J. B. M.
, Rutten
, M. C. M.
, Schurink
, G. W. H.
, Kose
, U.
, De Hart
, J.
, and Van De Vosse
, F. N.
, 2005, “A Patient-Specific Computational Model of Fluid-Structure Interaction in Abdominal Aortic Aneurysms
,” Med. Eng. Phys.
1350-4533, 27
(10
), pp. 871
–883
.31.
Maas
, H. G.
, Gruen
, A.
, and Papantoniou
, D.
, 1993, “Particle Tracking Velocimetry in 3-Dimensional Flows.1. Photogrammetric Determination of Particle Coordinates
,” Exp. Fluids
0723-4864, 15
(2
), pp. 133
–146
.32.
Malik
, N. A.
, Dracos
, T.
, and Papantoniou
, D. A.
, 1993, “Particle Tracking Velocimetry in 3-Dimensional Flows. 2. Particle Tracking
,” Exp. Fluids
0723-4864, 15
(4–5
), pp. 279
–294
.33.
Virant
, M.
, and Dracos
, T.
, 1997, “3d Ptv and Its Application on Lagrangian Motion
,” Meas. Sci. Technol.
0957-0233, 8
(12
), pp. 1539
–1552
.34.
Luthi
, B.
, Tsinober
, A.
, and Kinzelbach
, W.
, 2005, “Lagrangian Measurement of Vorticity Dynamics in Turbulent Flow
,” J. Fluid Mech.
0022-1120, 528
, pp. 87
–118
.35.
Kieft
, R. N.
, Schreel
, K. R. A. M.
, Van Der Plas
, G. A. J.
, and Rindt
, C. C. M.
, 2002, “The Application of a 3d Ptv Algorithm to a Mixed Convection Flow
,” Exp. Fluids
0723-4864, 33
(4
), pp. 603
–611
.36.
Hoyer
, K.
, Holzner
, M.
, Luthi
, B.
, Guala
, M.
, Liberzon
, A.
, and Kinzelbach
, W.
, 2005, “3d Scanning Particle Tracking Velocimetry
,” Exp. Fluids
0723-4864, 39
(5
), pp. 923
–934
.37.
Mathys
, R.
, and Zurflueh
, P.
, 2004, “Experimental Measurements of the Velocity Field Within an Anatomically Realistic Abdominal Aortic Aneurysm
,” Ph.D. thesis, ETH Zurich, Zurich, Switzerland.38.
Vignon-Clementel
, I. E.
, Figueroa
, C. A.
, Jansen
, K. E.
, and Taylor
, C. A.
, 2006, “Outflow Boundary Conditions for Three-Dimensional Finite Element Modeling of Blood Flow and Pressure in Arteries
,” Comput. Methods Appl. Mech. Eng.
0045-7825, 195
(29–32
), pp. 3776
–3796
.39.
Sahni
, O.
, Muller
, J.
, Jansen
, K. E.
, Shephard
, M. S.
, and Taylor
, C. A.
, 2006, “Efficient Anisotropic Adaptive Discretization of the Cardiovascular System
,” Comput. Methods Appl. Mech. Eng.
0045-7825, 195
(41–43
), pp. 5634
–5655
.40.
Vorp
, D. A.
, 2007, “Biomechanics of Abdominal Aortic Aneurysm
,” J. Biomech.
0021-9290, 40
(9
), pp. 1887
–1902
.41.
Li
, Z. H.
, and Kleinstreuer
, C.
, 2005, “Blood Flow and Structure Interactions in a Stented Abdominal Aortic Aneurysm Model
,” Med. Eng. Phys.
1350-4533, 27
(5
), pp. 369
–382
.42.
Chong
, C. K.
, and How
, T. V.
, 2004, “Flow Patterns in an Endovascular Stent-Graft for Abdominal Aortic Aneurysm Repair
,” J. Biomech.
0021-9290, 37
(1
), pp. 89
–97
.Copyright © 2009
by American Society of Mechanical Engineers
You do not currently have access to this content.
