This paper presents the modeling, design, and experimental validation of a self-energized sensor system for pressure measurement in the injection mold cavity using ultrasound as the information carrier. The sensor extracts energy from the polymer melt pressure and discretizes the pressure information into ultrasonic pulses for wireless transmission through the mold to a remote receiver. Analytical and numerical models are presented for three constituent components of the sensor: the energy converter, the threshold modulator, and the signal transmitter. Quantitative results were obtained to guide the parametric design of each constituent component. Simulations and experimental studies have validated the functionality of each individual component, as well as the sensor as an integrated unit. In addition to the injection mold pressure measurement, the sensing technique developed is applicable in a broad range of process monitoring applications where high pressure fluctuations occur.
Issue Section:
Technical Papers
Keywords:
injection moulding,
pressure measurement,
pressure sensors,
ultrasonic applications,
process control,
wireless sensor networks
Topics:
Cavities,
Design,
Power converters,
Pressure,
Pressure measurement,
Sensors,
Signals,
Pressure sensors
1.
Rawabdeh
, I. A.
, and Petersen
, P. F.
, 1999
, “In-Line Monitoring of Injection Molding Operations: A Literature Review
,” J. Injection Molding Technol.
, 3
, pp. 47
–53
.2.
Watkins
, B.
, 1997
, “Five Myths About Sensing Mold Pressure
,” Sensors Magazine
, 14
, pp. 73
–78
.3.
Collins
, C.
, 1999
, “Monitoring Cavity Pressure Perfects Injection Molding
,” Assembly Automation
, 19
(3
), pp. 197
–202
.4.
Langkamp
, U.
, 1996
, “Pressure and Temperature Sensors
,” Kunststoffe Plast Europe
, 86
(12
), pp. 1804
–1812
.5.
Weller
, S.
, 2000
, “Inner Pressure Measurement During Injection Moulding
,” Kunststoffe Plast Europe
, 90
(5
), pp. 20
–21
.6.
Huang
, J.
, and Cheng
, S.
, 2002
, “Study of Injection Molding Pressure Sensor With Low Cost and Small Probe
,” Sens. Actuators, A
, 101
(3
), pp. 269
–274
.7.
Luo, R. C., and Tsai, C. S., 2001, “Thin Film PZT Pressure/Temperature Sensory Arrays for On-Line Monitoring of Injection Molding,” Proceedings of Industrial Electronics Conference, 3, pp. 375–380.
8.
Luo, R. C., and Chen, C. M., 2000, “PZT Thin Film Pressure Sensor for On-Line Monitoring Injection Molding,” Proceedings of Industrial Electronics Conference, 4, pp. 2394–2399.
9.
Luo, R. C., and Chen, O., 1998, “MEMS Based Thin Film Pressure/Temperature Sensor for On-Line Monitoring Injection Molding,” Proceedings of Industrial Electronics Conference, 3, pp. 1306–1309.
10.
Akar
, O.
, Akin
, T.
, and Najafi
, K. A.
, 2001
, “Wireless Batch Sealed Absolute Capacitive Pressure Sensor
,” Sens. Actuators, A
, 95
(1
), pp. 29
–38
.11.
Buff
, W.
, Klett
, S.
, Rusko
, M.
, Ehrenpfordt
, J.
, and Goroll
, M.
, 1998
, “Passive Remote Sensing for Temperature and Pressure Using SAW Resonator Devices
,” IEEE Trans. Ultrason. Ferroelectr. Freq. Control
, 45
(5
), pp. 1388
–1392
.12.
Fonseca
, M. A.
, English
, J. M.
, von Arx
, M.
, and Allen
, M. G.
, 2002
, “Wireless Micromachined Ceramic Pressure Sensor for High-Temperature Applications
,” J. Microelectromech. Syst.
, 11
(4
), pp. 337
–343
.13.
Chatzandroulis
, S.
, Tsoukalas
, D.
, and Neukomm
, P. A.
, 2000
, “A Miniature Pressure System With a Capacitive Sensor and a Passive Telemetry Link for Use in Implantable Applications
,” J. Microelectromech. Syst.
, 9
(1
), pp. 18
–23
.14.
DeHennis, A., and Wise, K. D., 2002, “A Double-Sided Single-Chip Wireless Pressure Sensor,” Proceedings of the IEEE Microelectromechanical Systems, pp. 252–255.
15.
Ristic, V. M., 1983, Principles of Acoustic Devices, John Wiley & Sons, New York.
16.
Rafizadeh, M., Kamal, M. R., and Patterson W. I., 1997, “Physically-Based Adaptive Control of Cavity Pressure in Injection Molding: Filling Phase,” Proceedings of ANTEC, 1, pp. 582–587.
17.
Haykin, S., 1989, An Introduction to Analog and Digital Communications, John Wiley & Sons, Inc., New York, NY.
18.
Feher, K., 1995, Wireless Digital Communications: Modulation and Spread Spectrum Applications, Prentice Hall, Upper Saddle River, NJ.
19.
Randeraat, J. Van, and Setterington, R. E., 1974, Piezoelectric Ceramics, 2nd Ed. London: Mullard.
20.
Mattiat, O. E., 1971, Ultrasonic Transducer Materials, Plenum Press, New York-London.
21.
Mason, W. P., 1948, Electro-Mechanical Transducers and Wave Filters, Princeton, Van Nostrand, NJ.
22.
Redwood
, M.
, 1961
, “Transient Performance of a Piezoelectric Transducer
,” J. Acoust. Soc. Am.
, 33
, pp. 527
–536
.23.
Sittig
, E. K.
, 1967
, “Transmission Parameters of Thickness-Driven Piezoelectric Transducers Arranged in Multiplayer Configurations
,” IEEE Trans. Sonics Ultrason.
, SU-14
(4
), pp. 167
–174
.24.
Sittig
, E. K.
, 1969
, “Effects of Bonding and Electrode Layers on the Transmission Parameters of Piezoelectric Transducers Used in Ultrasonic Digital Delay Lines
,” IEEE Trans. Sonics Ultrason.
, SU-16
(1
), pp. 2
–10
.25.
Neter, J., 1996, Applied Linear Statistical Models, Fourth Edition, McGraw-Hill, pp. 641–643.
26.
Theurer, C., Zhang, L., Gao, R., and Kazmer, D., 2001, “Acoustic Telemetry in Injection Molding,” Society of Plastics Engineers Annual Technical Conference, Process Monitoring and Control Division, 51(3), pp. 208–213.
27.
Desilets
, C. S.
, Fraser
, J. D.
, and Kino
, G. S.
, 1978
, “The Design of Efficient Broad-Band Piezoelectric Transducers
,” IEEE Trans. Sonics Ultrason.
, SU-25
(3
), pp. 115
–125
.Copyright © 2004
by ASME
You do not currently have access to this content.
