The Laboratory of Transport Technology (Ghent University) converted a GM/Crusader V-8 engine for hydrogen use. The engine is intended for the propulsion of a midsize hydrogen city bus for public demonstration. For a complete control of the combustion process and to increase the resistance to backfire (explosion of the air–fuel mixture in the intake manifold), a sequential timed multipoint injection of hydrogen and an electronic management system is chosen. The results as a function of the engine parameters (ignition timing, injection timing and duration, injection pressure) are given. Special focus is given to topics related to the use of hydrogen as a fuel: ignition characteristics (importance of electrode distance), quality of the lubricating oil (crankcase gases with high contents of hydrogen), oxygen sensors (very lean operating conditions), and noise reduction (configuration and length of intake pipes). The advantages and disadvantages of a power regulation only by the air-to-fuel ratio (as for diesel engines) against a throttle regulation (normal gasoline or gas regulation) are examined. Finally, the goals of the development of the engine are reached: power output of 90 kW, torque of 300 Nm, extremely low emission levels, and backfire-safe operation.

Issue Section:
Internal Combustion Engines: Hydrogen-fueled Engines
Keywords:
engines, hydrogen economy, gas mixtures, fuel, combustion, lubrication, gas sensors, noise abatement, emission
Topics:
Engines, Fuels, Hydrogen, Ignition
1.
Das
,
L. M.
,
1990
, “
Fuel Induction Techniques for a Hydrogen Operated Engine
,”
Int. J. Hydrogen Energy
,
15
, pp.
823
–
842
.
2.
Sorusbay, C., Veziroglu, T. N., 1988, “Mixture Formation Techniques for Hydrogen-Fueled Internal Combustion Engines,” Proceedings of the 7th World Hydrogen Energy Conference, Vol. 3, Moscow, pp. 1909–1921.
3.
Kondo, T., Hiruma, M., and Furuhama, S., 1996, “A Study on the Mechanism of Backfire in External Mixture Formation Hydrogen Engines,” Proceedings of the 11th World Hydrogen Energy Conference, Vol. 2, Stuttgart, June 23–28. pp. 1547–1556.
4.
Lee
,
S. T.
,
Yi
,
H. S.
, and
Kim
,
E. S.
,
1995
, “
Combustion Characteristics of Intake Port Injection Type Hydrogen Fueled Engine
,”
Int. J. Hydrogen Energy
,
20
, pp.
317
–
322
.
5.
Guo
,
L. S.
,
Lu
,
H. B.
, and
Li
,
J. D.
,
1999
, “
A Hydrogen Injection System With Solenoid Valves for a Four-Cylinder Hydrogen-Fueled Engine
,”
Int. J. Hydrogen Energy
,
24
, pp.
377
–
382
.
6.
Sierens, R., and Rosseel, E., 1995, “Development of a Multi-Point Timed Injection S.I. Natural Gas Engine,” Natural Gas and Alternative Fuels for Engines, Vol. 24, ASME, New York, pp. 99–104.
7.
Sierens, R., and Rosseel, E., 1995, “Sequential Injection of Gaseous Fuels,” 5th Int. EAEC Congress, Strasbourg, June 1995, Paper No. SIA 9506A03.
8.
Furuhama, S., 1995, “Problems of Forecasting the Future of Advanced Engines and Engine Characteristics of the Hydrogen Injection With LH2 Tank and Pump,” Calvin Rice Lecture, ASME, 23 April 1995.
9.
Sierens, R., and Rosseel, E., 1998, “Variable Composition Hydrogen/Natural Gas Mixtures for Increased Engine Efficiency and Decreased Emissions,” ASME 1998 Spring Engine Technology Conference, Fort Lauderdale, FL, Apr. 26–29, Paper No. 98-ICE-105.
10.
Sierens, R., 1999, “The Development of a Hydrogen Fueled V-8 Engine,” 7th Int. EAEC Congres, Barcelona, June 1999, Paper No. STA99C435.
11.
Sierens, R., and Rosseel, E., 1998, “Backfire Mechanism in a Carburetted Hydrogen Fueled Engine,” Proceedings of the 12th World Hydrogen Energy Conference, Vol. 2, Buenos Aires, June 21–25, pp. 1537–1546.
12.
Payvey, M., 1988, “Fuel From Water,” Louisville, Merit Products.
13.
Van Boxlaer, L., and Poot, T., 1998, “Optimalisatie van een inlaatsysteem voor een waterstofmotor (The optimization of the intake manifold of a hydrogen fueled engine),” End of year thesis, Laboratory of Transporttechnology, University of Gent, Belgium.
Copyright © 2001
 by ASME
You do not currently have access to this content.