The next generation nuclear power/advanced gas reactor (NGNP/AGR) fuel development and qualification program included the design, installation, and testing of a 6-in. diameter nuclear fuel particle coater to demonstrate quality tri-structural isotropic (TRISO) fuel production on a small industrial scale. Scale-up from the laboratory-scale coater faced challenges associated with an increase in the kernel charge mass, kernel diameter, and a redesign of the gas distributor to achieve adequate fluidization throughout the deposition of the four TRISO coating layers. TRISO coatings are applied at very high temperatures in atmospheres of dense particulate clouds, corrosive gases, and hydrogen concentrations over 45% by volume. The severe environment, stringent product and process requirements, and the fragility of partially-formed coatings limit the insertion of probes or instruments into the coater vessel during operation. Pressure instrumentation were installed on the gas inlet line and exhaust line of the 6-in. coater to monitor the bed differential pressure and internal pressure fluctuations emanating from the fuel bed as a result of bed and gas “bubble” movements. These instruments are external to the particle bed and provide a glimpse into the dynamics of fuel particle bed during the coating process and data that could be used to help ascertain the adequacy of fluidization and, potentially, the dominant fluidization regimes. Pressure fluctuation and differential pressure data are not presently useful as process control instruments, but data suggest a link between the pressure signal structure and some measurable product attributes that could be exploited to get an early estimate of the attribute values.
Skip Nav Destination
e-mail: douglas.marshall@inl.gov
e-mail: charles.barnes@inl.gov
Article navigation
January 2010
Research Papers
Mining Process and Product Information From Pressure Fluctuations Within a Fuel Particle Coater
Douglas W. Marshall,
Douglas W. Marshall
Department of Fuel Fabrication, Battelle Energy Alliance, LLC, Idaho National Laboratory,
e-mail: douglas.marshall@inl.gov
U. S. Department of Energy
, P.O. Box 1625, Idaho Falls, ID 83415-3855
Search for other works by this author on:
Charles M. Barnes
Charles M. Barnes
Department of Fuel Fabrication, Battelle Energy Alliance, LLC, Idaho National Laboratory,
e-mail: charles.barnes@inl.gov
U. S. Department of Energy
, P.O. Box 1625, Idaho Falls, ID 83415-3855
Search for other works by this author on:
Douglas W. Marshall
Department of Fuel Fabrication, Battelle Energy Alliance, LLC, Idaho National Laboratory,
U. S. Department of Energy
, P.O. Box 1625, Idaho Falls, ID 83415-3855e-mail: douglas.marshall@inl.gov
Charles M. Barnes
Department of Fuel Fabrication, Battelle Energy Alliance, LLC, Idaho National Laboratory,
U. S. Department of Energy
, P.O. Box 1625, Idaho Falls, ID 83415-3855e-mail: charles.barnes@inl.gov
J. Eng. Gas Turbines Power. Jan 2010, 132(1): 012905 (7 pages)
Published Online: October 2, 2009
Article history
Received:
November 14, 2008
Revised:
November 25, 2008
Published:
October 2, 2009
Citation
Marshall, D. W., and Barnes, C. M. (October 2, 2009). "Mining Process and Product Information From Pressure Fluctuations Within a Fuel Particle Coater." ASME. J. Eng. Gas Turbines Power. January 2010; 132(1): 012905. https://doi.org/10.1115/1.3126772
Download citation file:
Get Email Alerts
Cited By
Image-based flashback detection in a hydrogen-fired gas turbine using a convolutional autoencoder
J. Eng. Gas Turbines Power
Fuel Thermal Management and Injector Part Design for LPBF Manufacturing
J. Eng. Gas Turbines Power
An investigation of a multi-injector, premix/micromix burner burning pure methane to pure hydrogen
J. Eng. Gas Turbines Power
Related Articles
Hydrodynamic Performance of a Novel Design of Pressurized Fluidized Bed Combustor
J. Energy Resour. Technol (June,2006)
High-Temperature Erosive Wear Behavior of High-Velocity Oxy-Fuel Sprayed Cr 3 C 2 25 (Ni20Cr) Coating on (AISI 316) Austenitic Steel
J. Tribol (July,2020)
Results of Tests to Demonstrate a 6-in.-Diameter Coater for Production of TRISO-Coated Particles for Advanced Gas Reactor Experiments
J. Eng. Gas Turbines Power (September,2009)
Flow Regime Study of a Light Material in an Industrial Scale Cold Flow Circulating Fluidized Bed
J. Energy Resour. Technol (June,2006)
Related Proceedings Papers
Related Chapters
Gas-Fluidized Beds
Two-Phase Heat Transfer
Some Aspects of Russian Regulation and Codes in Nuclear Power
Global Applications of the ASME Boiler & Pressure Vessel Code
Introduction
Nuclear Reactor Thermal-Hydraulics: Past, Present and Future