In this work, the minimization of warpage was investigated using the “moldflow” software and sequential simplex algorithm based on feedstock properties. Also, the sensitivity analysis was implemented to determine the degree of impact of each parameter on the warpage. This study is divided into two portions: experimental analysis and numerical analysis. First, for the experimental study, four kinds of feedstock with different alumina powder loadings were prepared to investigate the rheological properties. This investigation showed that the feedstock with 60 vol. % alumina powder was the optimum feedstock for the injection molding. Also, the results indicated that the viscosity of feedstock decreases by increasing both the shear rate and temperature. Next, the thermal conductivity of this feedstock was measured at different temperatures and it was found that the change of temperature can greatly influence the thermal conductivity of feedstock. In the numerical study, the injection molding parameters were divided into three categories. Based on the feedstock properties obtained form the first portion, and in order to minimize the warpage, the values of these parameters were sequentially acquired by moldflow and used in the sequential simplex algorithm for gradual convergence to the optimum level. To show the accuracy of numerical results, several samples were injection molded using the injection molding conditions for each vertex; results showed a close correlation between the values obtained by the numerical simulation and by the actual case. After determining the optimum parameter values, the sensitivity analysis was performed to identify the level of influence of each parameter on warpage. The obtained results showed that the most effective parameters on warpage are the mold temperature, packing pressure, and the holding time. Generally, it is demonstrated that the experimental and numerical analysis, performed via the moldflow software and sequential simplex algorithm, together with the sensitivity analysis can be useful in achieving success in the powder injection molding (PIM) technique.
Skip Nav Destination
Article navigation
February 2013
Research-Article
Optimization of the Powder Injection Molding Process Parameters Using the Sequential Simplex Algorithm and Sensitivity Analysis
Ali Keshavarz Panahi,
Ali Keshavarz Panahi
1
e-mail: Panahi@mecheng.iust.ac.ir
1Corresponding author.
Search for other works by this author on:
Mohamad Hussaini Fareed
Mohamad Hussaini Fareed
School of Mechanical Engineering
,Iran University of Science and Technology
,Tehran 16846
, Iran
Search for other works by this author on:
Ali Keshavarz Panahi
e-mail: Panahi@mecheng.iust.ac.ir
Mohamad Hussaini Fareed
School of Mechanical Engineering
,Iran University of Science and Technology
,Tehran 16846
, Iran
1Corresponding author.
Contributed by the Manufacturing Engineering Division of ASME for publication in the Journal of Manufacturing Science and Engineering. Manuscript received April 28, 2011; final manuscript received October 29, 2012; published online January 22, 2013. Assoc. Editor: Allen Y. Yi.
J. Manuf. Sci. Eng. Feb 2013, 135(1): 011006 (7 pages)
Published Online: January 22, 2013
Article history
Received:
April 28, 2011
Revision Received:
October 29, 2012
Citation
Keshavarz Panahi, A., Mianajiy, H., Miandoabchi, E., and Hussaini Fareed, M. (January 22, 2013). "Optimization of the Powder Injection Molding Process Parameters Using the Sequential Simplex Algorithm and Sensitivity Analysis." ASME. J. Manuf. Sci. Eng. February 2013; 135(1): 011006. https://doi.org/10.1115/1.4023301
Download citation file:
Get Email Alerts
Related Articles
Process-Driven Input Profiling for Plastics Processing
J. Manuf. Sci. Eng (August,2007)
Effect of Binder Constituents and Solids Loading on the Rheological Behavior of Irregular Iron-Based Feedstocks
J. Manuf. Sci. Eng (March,2021)
Integrated Flow Analysis During Filling and Post-Filling Stage of Semiconductor Encapsulation
J. Electron. Packag (March,2000)
Performance of a Modified Packed-Gland Seal
J. of Lubrication Tech (April,1968)
Related Chapters
Optimization of an Irregular 2D Packing Problem by a Genetic-Based Heuristic Algorithm
International Conference on Computer and Automation Engineering, 4th (ICCAE 2012)
Natural Gas Transmission
Pipeline Design & Construction: A Practical Approach, Third Edition
Simulation and Optimization of Injection Process for LCD Cover
Proceedings of the 2010 International Conference on Mechanical, Industrial, and Manufacturing Technologies (MIMT 2010)