...Gabriel T Paula; João P Pascon An alternative finite element formulation to predict ductile damage and fracture in highly deformable materials is presented. For this purpose, a finite-strain elastoplastic model based on the Gurson-Tvergaard-Needleman (GTN) formulation is employed, in which...

...) technology, while the computational analysis covered the finite element (FE) modeling of the 3D-printed samples. The research focused on evaluating the tensile strength and fatigue resistance of the specimens printed in various orientations, alongside a detailed investigation of their fracture behavior...

...Kais Jribi; Boutros Azizi; Alberto W. Mello This study thoroughly examines the mechanical properties of carbon fiber-reinforced polymers (CFRPs), motivated by the critical need for accurate composite property data in investigating fracture control measures for structures subjected to barely visible...

... Figure finite element (FE) method damage higher-order polynomial sensitivity analysis (SA) constitutive relations fracture mechanical behavior elasto-plastic model strain rate Fire-reinforced polymeric composite structures are increasingly adopted in various engineering...

... elements (CAX4). Graphical Abstract Figure Environmental effects fracture mechanical behavior microstructure property relationships plastic behavior National Natural Science Foundation of China 10.13039/501100001809 52075434 The UMAT subroutine's...

... of hybrid reinforcements within the surface composite. The results demonstrate that the inclusion of reinforcements in magnesium-based alloy led to an enhancement in fracture toughness, mitigation of crack propagation, and an overall improvement in fracture resistance to catastrophic failure. 1...

... softening behavior, and ɛ p is the effective plastic strain and e = exp(1). For the fiber–matrix, bead–matrix, and fiber–bead interfaces, the cohesive zone model is used to delineate the fracture behavior [ 21 ]. The tractions at the interface are written as T n = { ( 1 − D...

...Gabriel Anichowski; Riley Damm; Ahmet Kahraman; Isaac Hong Tooth bending fatigue failure is a primary design concern for gear designers in power transmission applications. Fracture of a gear tooth in operation results in overload conditions to adjacent teeth, which cascades into potential failure...

... of Statistical Fatigue Damage Assessment for Stochastic Loadings ,” Int. J. Fatigue , 132 , p. 105327 . 10.1016/j.ijfatigue.2019.105327 [12] Manson , S. S. , 1966 , “ Interfaces Between Fatigue Creep and Fracture ,” Int. J. Fract. Mech. , 2 ( 1 ), pp. 327 – 363 . 10.1007/BF00698478 [13...

... . This work is in part a work of the U.S. Government. ASME disclaims all interest in the U.S. Government's contributions. 19 05 2023 14 11 2023 14 11 2023 12 01 2024 fatigue additive manufacturing SEM aluminum alloys EBSD fracture materials processing microstructure...

... modulus of micro-machined samples are surprisingly lower, while failure strain is highest among line filling printed samples. Damage resistance was quantified in terms of work of fracture, and hexagonal filling provided better damage resistance than line filling patterns for conditions of 0 deg raster...

...Vishwas Divse; Suhas S. Joshi; Deepak Marla This work presents a 3D progressive damage model based on Puck’s failure theory and linear damage evolution in fiber-reinforced plastic (FRP) laminates. It includes shear nonlinearity, in situ strengths, equivalent stress–strain, and mixed-mode fracture...

...@prattwhitney.com Contributed by the Materials Division of ASME for publication in the J ournal of E ngineering M aterials and T echnology . 11 02 2023 21 08 2023 21 08 2023 14 09 2023 LPBF Mar M 509 heat treatment microstructure tensile properties fracture mechanical...

... — 0.3256 0.0897 The fatigue data obtained for each sample group are listed in Table 4 . The number of cycles-to-failure is recorded at fracture. The average and standard deviation of cycles-to-failure were determined. It is important to note that outlying observations or runout data points...

... 0 2 where G f is the fracture energy per unit volume, and h cb is the characteristic element size. Apart from the initial validation test, as shown in Fig. 2 , the simulations of this work were composed of two primary geometries, differentiated only by the location...

... elastic behavior fracture mechanical behavior metals polymers ceramics intermetallics and their composites microstructure property relationships plastic behavior Aluminum (Al) alloys can be used in several sectors including transportation, electrical, biomedical, aerospace, and military...

... in the preheated welded specimen. However, by increasing the preheat temperature further, the tensile strength decreases due to the formation of defects from excessive heat. The preheated sample fractured at the base metal, revealing a ductile fracture mode. Fig. 9 Microstructure of the cross section for 1750...

... on the fracture surface at the shear strain rate of 36,000 s −1 . Furthermore, the creation of voids is aided by a rise in initial temperature. The factors affecting the formation of adiabatic shear bands are explored based on the numerical simulation, which suggests that the magnitude of the temperature gradient...

... propagation prior to the transgranular cleavage fracture. Additionally, two material models were calibrated from the experimental static and cyclic experimental testing. The characterization of the fatigue behavior of wrought Fe–Co–2V presented herein will aid in the fatigue analysis of Fe–Co–2V components...

.../s00170-021-08566-2 . [8] Bozzi , S. , Helbert-Etter , A. L. , Baudin , T. , Klosek , V. , Kerbiguet , J. G. , and Criqui , B. , 2010 , “ Influence of FSSW Parameters on Fracture Mechanisms of 5182 Aluminium Welds ,” J. Mater. Process. Technol. , 210 ( 11 ), pp. 1429...