..., reciprocating ball-on-plate configuration) The reciprocating sliding wear tests were conducted on a ball-on-plate configuration (Fig. 1 ). The details of the wear test are described in Ref. [ 35 ]. The wear process in the examined material depends on the counterpart used, since its wear changes the shape...

... Graphical Abstract Figure high temperature Ni-doped hBN solid lubricants composites friction sliding wear With the continuous advancement of technology, there is an increasing demand for materials that can provide low friction and low wear properties over a wide range of temperatures...

.... , and Lee , J. M. , 2000 , “ Influence of Porosity on Dry Sliding Wear Behavior in Spray Deposited Al–6Cu–Mn/SiCp Composite ,” Mater. Sci. Eng. A , 293 ( 1–2 ), pp. 146 – 156 . 10.1016/S0921-5093(00)01052-2 [54] Ocelík , V. , Matthews , D. , and De Hosson , J. T. M. , 2005...

...@itbhu.ac.in Email: ranjan@rowan.edu Contributed by the Tribology Division of ASME for publication in the J ournal of T ribology . 07 11 2021 21 01 2022 22 01 2022 15 02 2022 friction wear magnetron sputtering coatings Ti-based coatings sliding wear Due...

... QP980 Three experimental tests, i.e., Tests #1, #2, and #3 (see Table 3 ), were conducted to investigate the sliding wear of three tool materials, i.e., Cr12MoV, SKD11, and DC53. The tool samples #1 to #3 listed in Table 3 were treated by the VHT. In practice, the surface hardness...

... studied. The sliding wear properties of the Conventional and the Bimodal against Si 3 N 4 counterballs under different loads at room temperature (∼25 °C) were investigated using a friction and wear tester. Compared with the Conventional, the Bimodal has denser microstructure, lower porosity, more...

...Qingliang Wang; Li Meng; Hui Chen; Qihao Zheng This work reports on the sliding wear properties of Fe 3 Al-based alloy in conditions of dry sliding and quartz sand abrasion. The wear strengthening mechanism is also analyzed in detail. On this basis, the feasibility of using Fe 3 Al-based alloy...

... manufacturing sliding wear wear testing surface analysis two-body abrasion AlSi10Mg alloy surface properties and characterization friction wear 17 04 2020 07 07 2020 08 07 2020 03 08 2020 Contributed by the Tribology Division of ASME for publication in the J ournal of T...

... model are bridged to study the transient interdependent relationship between the sliding wear behavior and the mixed-EHL performance. In order to consider the effect of the transient mixed-EHL performance on the sliding wear, the Archard model is extended to include the time-varying wear coefficient...

...J. An; W. Zhao; C. Q. Feng Dry sliding wear characteristics of the as-cast Mg–10.1Gd–1.4Y–0.4Zr alloy were investigated at 3.0 m/s within a temperature range of 20–200 °C on a pin-on-disc type wear testing machine. Wear rates were acquired and plotted against load at each test temperature...

... the tribological performance of an experimental Ti−Si−Zr alloy. The effect of Al content on the alloy's microstructure and mechanical properties was evaluated using X-ray diffraction (XRD), scanning electron microscopy (SEM), and Vickers hardness measurements. Sliding wear testing was performed in a ball-on-disk...

... of ASME for publication in the J OURNAL OF T RIBOLOGY . Manuscript received February 20, 2018; final manuscript received August 16, 2018; published online October 16, 2018. Assoc. Editor: Sinan Muftu. 20 02 2018 16 08 2018 sliding wear ceramic–matrix nanocomposites structure...

... Reinforced by Short Carbon Fibers and Zirconium Dioxide Nanoparticles: Mechanical Properties and Sliding Wear Behavior With Water Lubrication ,” J. Appl. Polym. Sci. , 119 ( 3 ), pp. 1711 – 1720 . 10.1002/app.32847 [23] Xiaochen , H. , Ying , H. , Xiyu , H. , and Dong , J. , “ Poly...

... temperature has significant effect on the performance of the braking material. Thereby, the tribological and the mechanical properties of the novel material were found to be temperature sensitive. brake materials sliding wear copper matrix composite dry sliding wear testing sliding friction...

...-2Nb alloy in vacuum is almost lower by an order of magnitude than that in air. intermetallics high vacuum space sliding wear Because of lightweight, high strength from room temperature to elevated temperature, good corrosion, and oxidation resistance, intermetallic γ-TiAl based alloys...

... layers.” Fig. 14 Schematic illustration of the contact modes for the sliding wear of short-fiber-reinforced polymer composites against metallic counterparts covered with TFLs When the values of λ were relatively small, e.g., less than 0.1, TFLs were considered as “insufficiently...

.... 08 07 2012 16 12 2012 The evolution of the maximum contact stresses in amorphous carbon coated silicon during sliding wear against a Si 3 N 4 ball was investigated. Amorphous carbon coating was prepared on a silicon substrate by the electron cyclotron resonance (ECR) plasma sputtering...

... with the bainitic and austenitic steels. 06 05 2010 18 12 2010 17 03 2011 17 03 2011 abrasion austenitic steel plastic deformation rails railways sliding friction pearlite bainite austenite ferrite sliding wear adhesion third-body abrasion mild oxidation...

... hardness, impact toughness, abrasive wear, sliding wear, and contact fatigue performance tests, indicated that despite the similar abrasive and sliding wear resistance of both alloys, the HIPed alloy exhibited an improved contact fatigue and impact toughness performance in comparison to the cast...

... 2008 03 12 2008 aluminium alloys carbon fibre reinforced composites copper eutectic alloys silicon alloys sliding friction wear wear testing sliding wear electroless copper coating graphite short carbon fiber Light weight and fuel efficiency in automobile industries...