In axial turbine, the tip clearance flow occurring in rotor blade rows is responsible for about one-third of the aerodynamic losses in the blade row and in many cases is the limiting factor for the blade lifetime. The tip leakage vortex forms when the leaking fluid crosses the gap between the rotor blade tip and the casing from pressure to suction side and rolls up into a vortex on the blade suction side. The flow through the tip gap is both of high velocity and of high temperature, with the heat transfer to the blade from the hot fluid being very high in the blade tip area. In order to avoid blade tip burnout and a failure of the machine, blade tip cooling is commonly used. This paper presents the physical study and an improved design of a recessed blade tip for a highly loaded axial turbine rotor blade with application in high pressure axial turbines in aero engine or power generation. With use of three-dimensional computational fluid dynamics (CFD), the flow field near the tip of the blade for different shapes of the recess cavities is investigated. Through better understanding and control of cavity vortical structures, an improved design is presented and its differences from the generic flat tip blade are highlighted. It is observed that by an appropriate profiling of the recess shape, the total tip heat transfer Nusselt number was significantly reduced, being 15% lower than the flat tip and 7% lower than the base line recess shape. Experimental results also showed an overall improvement of 0.2% in the one-and-a-half-stage turbine total efficiency with the improved recess design compared to the flat tip case. The CFD analysis conducted on single rotor row configurations predicted a 0.38% total efficiency increase for the rotor equipped with the new recess design compared to the flat tip rotor.
Skip Nav Destination
e-mail: bob.mischo@lsm.iet.mavt.ethz.ch
Article navigation
April 2008
Research Papers
Flow Physics and Profiling of Recessed Blade Tips: Impact on Performance and Heat Load
Bob Mischo,
Bob Mischo
Turbomachinery Laboratory,
e-mail: bob.mischo@lsm.iet.mavt.ethz.ch
Swiss Federal Institute of Technology
, CH-8092 Zürich, Switzerland
Search for other works by this author on:
Thomas Behr,
Thomas Behr
Turbomachinery Laboratory,
Swiss Federal Institute of Technology
, CH-8092 Zürich, Switzerland
Search for other works by this author on:
Reza S. Abhari
Reza S. Abhari
Turbomachinery Laboratory,
Swiss Federal Institute of Technology
, CH-8092 Zürich, Switzerland
Search for other works by this author on:
Bob Mischo
Turbomachinery Laboratory,
Swiss Federal Institute of Technology
, CH-8092 Zürich, Switzerlande-mail: bob.mischo@lsm.iet.mavt.ethz.ch
Thomas Behr
Turbomachinery Laboratory,
Swiss Federal Institute of Technology
, CH-8092 Zürich, Switzerland
Reza S. Abhari
Turbomachinery Laboratory,
Swiss Federal Institute of Technology
, CH-8092 Zürich, SwitzerlandJ. Turbomach. Apr 2008, 130(2): 021008 (8 pages)
Published Online: February 29, 2008
Article history
Received:
June 27, 2006
Revised:
August 18, 2006
Published:
February 29, 2008
Citation
Mischo, B., Behr, T., and Abhari, R. S. (February 29, 2008). "Flow Physics and Profiling of Recessed Blade Tips: Impact on Performance and Heat Load." ASME. J. Turbomach. April 2008; 130(2): 021008. https://doi.org/10.1115/1.2775485
Download citation file:
Get Email Alerts
A Digital Engineering Analysis of an Additively-Manufactured Turbine Vane
J. Turbomach (May 2025)
Mode Analysis for the Rotating Aerodynamic Disturbance of a Transonic Fan
J. Turbomach (May 2025)
Effect of Ceramic Matrix Composites on the Thermal Efficiency of a Power Generation Turbine
J. Turbomach (May 2025)
Heat Transfer Enhancement in Pulsating Flows: A Bayesian Approach to Experimental Correlations
J. Turbomach (May 2025)
Related Articles
Aerodynamics of Tip Leakage Flows Near Partial Squealer Rims in an Axial Flow Turbine Stage
J. Turbomach (January,2005)
Improving Efficiency of a High Work Turbine Using Nonaxisymmetric Endwalls—Part II: Time-Resolved Flow Physics
J. Turbomach (April,2010)
Optimized Shroud Design for Axial Turbine Aerodynamic Performance
J. Turbomach (July,2008)
Fluid Dynamics and Performance of Partially and Fully Shrouded Axial Turbines
J. Turbomach (October,2005)
Related Proceedings Papers
Related Chapters
Introduction
Turbine Aerodynamics: Axial-Flow and Radial-Flow Turbine Design and Analysis
Control and Operational Performance
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Outlook
Closed-Cycle Gas Turbines: Operating Experience and Future Potential