Wake-induced laminar-turbulent transition is studied at the leading edge of a C4-section compressor stator blade in a 1.5-stage axial compressor. Surface hot-film sensor observations are interpreted with the aid of numerical solutions from UNSFLO, a quasi-three-dimensional viscous-inviscid flow solver. The passage of a rotor wake, with its associated negative jet, over the stator leading edge is observed to have a destabilizing effect on the suction surface boundary layer. This leads to transition closer to the stator leading edge than would have occurred under steady flow conditions. The strength of this phenomenon is influenced by the rotor-stator axial gap and the variability of individual rotor wake disturbances. A variety of transition phenomena is observed near the leading edge in the wake path. Wave packets characteristic of Tollmien-Schlichting waves are observed to amplify and break down into turbulent spots. Disturbances characteristic of the streaky structures occurring in bypass transition are also seen. Examination of suction surface disturbance and wake-induced transitional strip trajectories points to the leading edge as the principal receptivity site for suction surface transition phenomena at design loading conditions. This contrasts markedly with the pressure surface behavior, where transition at design conditions occurs remotely from leading-edge flow perturbations associated with wake chopping. Here, the local receptivity of the boundary layer to the wake passing disturbance and turbulent wake fluid discharging onto the blade surface may be of greater importance.
Skip Nav Destination
e-mail: alan.henderson@utas.edu.au
e-mail: greg.walker@utas.edu.au
Article navigation
April 2008
Research Papers
Unsteady Transition Phenomena at a Compressor Blade Leading Edge
Alan D. Henderson,
Alan D. Henderson
School of Engineering,
e-mail: alan.henderson@utas.edu.au
University of Tasmania
, Hobart, 7001, Australia
Search for other works by this author on:
Gregory J. Walker,
Gregory J. Walker
School of Engineering,
e-mail: greg.walker@utas.edu.au
University of Tasmania
, Hobart, 7001, Australia
Search for other works by this author on:
Jeremy D. Hughes
Jeremy D. Hughes
Search for other works by this author on:
Alan D. Henderson
School of Engineering,
University of Tasmania
, Hobart, 7001, Australiae-mail: alan.henderson@utas.edu.au
Gregory J. Walker
School of Engineering,
University of Tasmania
, Hobart, 7001, Australiae-mail: greg.walker@utas.edu.au
Jeremy D. Hughes
J. Turbomach. Apr 2008, 130(2): 021013 (10 pages)
Published Online: March 21, 2008
Article history
Received:
September 1, 2006
Revised:
October 5, 2006
Published:
March 21, 2008
Citation
Henderson, A. D., Walker, G. J., and Hughes, J. D. (March 21, 2008). "Unsteady Transition Phenomena at a Compressor Blade Leading Edge." ASME. J. Turbomach. April 2008; 130(2): 021013. https://doi.org/10.1115/1.2751148
Download citation file:
Get Email Alerts
Cited By
Evaluating Thin-Film Thermocouple Performance on Additively Manufactured Turbine Airfoils
J. Turbomach (July 2025)
Thermohydraulic Performance and Flow Structures of Diamond Pyramid Arrays
J. Turbomach (July 2025)
Related Articles
Observations of Transition Phenomena on a Controlled Diffusion Compressor Stator With a Circular Arc Leading Edge
J. Turbomach (July,2010)
Aerodynamic Blade Row Interactions in an Axial Compressor—Part I: Unsteady Boundary Layer Development
J. Turbomach (January,2004)
The Influence of Turbulence on Wake Dispersion and Blade Row Interaction in an Axial Compressor
J. Turbomach (January,2006)
Related Chapters
Introduction
Design and Analysis of Centrifugal Compressors
Other Components and Variations
Axial-Flow Compressors
Boundary Layer Analysis
Centrifugal Compressors: A Strategy for Aerodynamic Design and Analysis